Zenitsu - Urban Vibes Poster

If you want to sell prints of this model, as well as all of my models - future and past
Subscribe to My Patreon:

Or Subscribe for a commercial License Directly in Maker World:
 

MembershipC3D Commercial Membership - Authorized Merchant

 

 

Zenitsu – Urban Vibes blends street‑art grit with an anime icon ⚡🖤 Big hits of thunder‑yellow and deep black feel like city lights at night, and the tight crop puts the face and jacket right in your space 🟡🕶️ The rough, choppy textures read like a fresh screen‑print on a brick wall, with fractured shapes that look mid‑motion even when the piece is still 🧱🎨

 

Those round lenses aren’t just for style. They catch the yellow like little lightning halos and add a cool, focused vibe ⚡👓 Up close you can chase the layered shards and paint‑chip details; from a few steps back it snaps into a clean, high‑contrast silhouette that pops in studios, game corners, and con booths 🎮🖼️

 

Framed in black so the colors punch, it works as a solo statement or next to monochrome setups that need a jolt of street‑meets‑anime energy 🖤💥

 

Printing tips

Maker notes:

• Make sure to clean the build plate with dishwashing soap and warm water before printing. Handwashing soaps should never be used to clean build plates because moisturizers can harm adhesion 🧼💧
   

USE A LIGHTER! - a quick pass with a torch on the printed parts will get rid of the inevitable stringing that comes with this type of models.
 

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm

Filaments Used:
PLA Jayo Black Transmission Distance: 0.3 / Amazon
PLA Jayo Gray Transmission Distance: 2.2 / Amazon
PLA BambuLab Basic Orange Transmission Distance: 5
PLA KINGROON Yellow Transmission Distance: 5.5 / Amazon
PLA Anycubic Pantone Peach Fuzz Transmission Distance: 4.2 / Amazon
PLA KINGROON White Transmission Distance: 5.3 / Amazon

Color Pallete 6 Color Version:

Swap Instructions 6 Color Version:

Start with Black
    At layer #19 (1.6mm) swap to Gray
    At layer #22 (1.84mm) swap to Orange
    At layer #26 (2.16mm) swap to Yellow
    At layer #30 (2.48mm) swap to Peach Fuzz
    At layer #36 (2.96mm) swap to White for the rest.
 

Boost MeEnjoying this model? Give it a boost! 🌟 Your support helps my creations reach more makers—thank you for keeping the magic alive! ✨🚀

How to do more than 4 colors on a single AMS?

To use more than 4 colors with a single AMS is pretty simple when it comes to HueForges.

Always start the print from either Bambu Studio or Bambu Handy App - This will allow you to map the rolls of filaments to a certain slot in the AMS:

Now map the first 4 colors (which should already be inserted in the AMS to Slots 1 - 2 - 3 - 4
Once thats done move to maping colors 5 - 6 - 7 - 8 to respectively AMS Slots 1 - 2 - 3 - 4 again!

This will allow you to Change the rolls of filament once the printer is done with that color.
For example, in the picture above once we are done with the Black color (Which is usually first) we are going to remove the black roll (you can do that while printing) with White, then once Charcoal Black is done we are going to change that to Red, Dark Gray to Yellow and we are done. ~ You can do that with as many colors as you need!
YOU CAN PLACE A PAUSE ON THE LAST LAYER OF COLOR 4 TO AVOID HAVING TO BABYSIT THE PRINTER. ONCE PAUSED CHANGE 1-2-3 WITH 5-6-7 AND RESUME. IF YOU NEED MULTIPLE PAUSES YOU CAN DO THAT TOO

Drop me a follow!🤜🤛