"Say Goodbye to the Vacuum" — Streamline Maintenance with this Tray System
The proven debris tray system used by the P1, X1, P2S , and H2 series is now available for the Bambu Lab X2D. This model is specifically tailored to fit the internal chamber dimensions of the X2D, including clearance for the dual fan units.
Key Features
"Lift-and-Dump" Cleaning This 5-part tray system catches filament scraps, purge lines, and fine debris before they ever touch the printer floor. For cleaning, simply lift the entire unit out and empty it into the trash. It eliminates the need for vacuuming and keeps your printing environment pristine.
Smart "Filament Hinge" Mechanism The connection pins are designed to use standard 1.75mm filament. No extra hardware is required—just use your scrap filament. This hinge design allows the side trays to fold slightly, making it easy to remove the unit from the tight space between the X2D's fan units without any snagging.
Self-Guiding Door Alignment The tray is designed to be guided into its ideal position simply by placing it inside and closing the printer door. By relying on the chamber's geometry, it maintains a stable position during high-speed printing while remaining effortless to remove for maintenance.
Dimensions & Compatibility
Designed Dimensions: 290mm (W) × 304mm (D)
Confirmed Compatibility: Bambu Lab X2D
⚠️ IMPORTANT - Before You Print:
Measure the internal width of your printer from the left cooling fan unit to the cooling fan unit on the right. Ensure it is at least 290mm.
Ensure the internal depth is at least 304mm.
Print the Left Tray first as a test piece to verify proper fit before printing all components.
Due to individual printer tolerances, if the test piece does not install smoothly, consider adjusting your slicer settings.
Assembly Instructions
Print all five components (Front Extend, Front, Rear, Left, Right) according to your recommended settings.
Cut 1.75mm filament to the following lengths for the hinge pins:
266mm × 2 pieces (for the main left/right hinges)
248mm × 1 piece (to connect the Front and Front Extend trays)
Main Assembly: Align the Front and Rear trays with the Left and Right trays, then insert the two 266mm filament pins. After insertion, trim any excess filament flush with the outer edge of the hinges.
Extend Tray Attachment: Align the hinge holes of the Front tray and the Front Extend tray, then insert the 248mm filament pin to connect them. Trim the excess filament flush with the edge.
💡 Tip: If the filament is difficult to insert, try cutting the end at a 45° angle for easier threading.
Testing: Test the hinges by gently folding the left and right trays—they should move smoothly.
Installation Guide
Position the Set: Place the entire connected tray set into the printer. Ensure the Front and Rear sections are pushed all the way to their respective ends of the printer floor.
Place Left & Right Trays Finally, press down the left and right trays so they sit flush with the bottom and secure the full set in place.
Print Notes & Handling
Cooling: Wait for the build plate to cool down completely before removal. Attempting to peel it off while hot may cause the parts to warp or deform.
Bed Adhesion: Ensure your build plate (ideally the official Textured PEI Plate) is thoroughly degreased with dish soap or IPA. Avoid touching the surface with your bare hands, as skin oils can ruin adhesion.
Filament Condition (Dryness): Ensure your filament is dry before printing. Moisture-laden filament can cause stringing, bubbling, and poor surface finish. For hygroscopic materials like PETG, PLA, we recommend using a filament dryer or oven before use.
Calibration: If you experience failure with this print, it may indicate calibration issues that will affect your future projects. We recommend performing printer and filament calibrations beforehand.
Before You Use
Minor adjustments (light sanding) may be needed due to individual printer tolerances. Do not force installation.
Check Before Use: Ensure nothing interferes with moving parts (print head, bed, etc.) and that the tray set is fully seated and stable.
🛑 Use at your own risk. The designer is not responsible for any damage caused by use or misuse of this model.
Nanashi
