Boost MeThank you for inspiring me to create more excellent models!
If you like my design, feel free to click the “Buy Now” button (if available) on this page to support me. I may earn a small commission, which helps me keep creating more models. Thanks and have fun!
Introduction
A bird circulating shower device using the ZC003 rechargeable power kit, designed for budgerigars or similarly sized birds.
Similar projects typically use wired-powered finished water pumps, which must be placed near a power source, and routing cables is inconvenient when used in a birdcage. Most also do not provide mounting solutions.
The main goal of this project is a more flexible and convenient user experience, free from cable restrictions, allowing it to be placed inside or outside the cage, or mounted
Highlights
Flexible to use. It can be placed anywhere, or hung inside or outside the birdcage.
Quick-release power module. The power module and centrifugal pump are magnetically coupled, solving sealing issues while also allowing the power module to be removed at any time, making charging or cleaning the water basin more convenient.
Transparent viewing cover. Used for external mounting, it can be easily disassembled and assembled.
Water filtration platform. Provides a standing point for parrots, while filtering large particles of impurities, reducing the likelihood of clogging the water pump and shower.
Quick-release shower head. Initially available in two variants: straight and circular.
Sufficient battery life. Tested to last 3-4 hours, enough for daily use.
Tips
Birds may not always be willing to bathe, so don't be impatient if they don't immediately interact after the shower is placed.
Budgerigars are more willing to clean themselves in warm, sunny environments. The opposite is true in cold, gloomy weather.
When the shower is not in use, it can be left in place. Give the birds some time to get familiar with this small device, and they will lower their guard and be more likely to bathe later.
Precautions
Noise: Printing gear rings with flexible materials can significantly reduce noise, but it still exists. My budgerigars did not get scared after getting used to it in actual use.
Lubrication: If the printer accuracy and filament condition are good, there is no need to lubricate the gears. If lubrication is needed, it is recommended to use low-viscosity lubricating oil instead of grease, as the latter will significantly reduce the output speed and affect the pump's performance.
Filament:
The main body can be made of PLA/PETG. If the water basin leaks, it is mainly due to insufficient extrusion and excessive gaps between printed lines. Try increasing the flow rate.
The gear ring part uses flexible material. Tested with TPU 95A or TPU 90A, the performance difference between the two is small, but both are significantly better than PLA/PETG. It must be thoroughly dried before printing or printed while drying.
Magnets:
Arrange the magnets as shown in the figure, with adjacent magnets having opposite polarities.
Use pause printing for embedding; a pause G-code has been added to plate 1, so resume printing after placing the magnets.
Using magnets with different strengths will affect the magnetic coupling effect. Too strong a magnetic force will create greater impeller rotation resistance, leading to weakened water flow; too weak a magnetic force will cause decoupling slippage. This can be adjusted by increasing or decreasing the spacing. The default coupling distance has been optimized.
Storage: Place the power module where it is not easily accidentally touched. The power module can be adsorbed onto some iron products, strong adsorption force can impede the motor shaft's rotation. If you accidentally press the switch, the current might continuously generate heat and damage the motor.
Charging: Use 5V-1A input Unattended charging is not recommended.
AIGC
For a cleaner visual effect, the cover image was AI-modified; all other photos are original real shots.
Assembly Guide
Tools Required
Phillips screwdriver
Pliers
Utility knife or other cutting tool
Assembly
Cut plastic sheet A: 283mm x 112mm
Cut plastic sheet B, you can score and cut along the outer edge of this part
Plastic sheets usually have a protective film, remember to remove it
Use pliers to press in and fix the buckles on both sides
D2 x 10mm straight shaft
Screw in the screws included with the charging power kit here to secure the magnetic coupling and gear
Ensure to press firmly into place during installation
TeraE
