Large But Slim Bambu Lab Poop Bucket - Filament Waste Bin - X1 and X1 Carbon P1P P1S

Update 12 Nov : Print files have been optimised! Even shorter print time and lesser material now. Thank you.

Please click a LIKE on my product if you like it. Thank you, I will greatly appreciate it. Cheers!

Introduction

While testing my model https://makerworld.com/en/models/47982 AMS Fix Failed To Pull Out Filament Error, my waste bin got so full and i needed to empty it every few hours, figured that i needed a bigger one. Also i realised that there is some upgrade that can be done to the original model so…

I present to you the “Large But Slim Bambu Lab Poop Bucket - Filament Waste Bin - X1 and X1 Carbon P1P P1S”.

Some problems i met using the original bucket

-Small collection area so the bucket fills up quickly.

-The angle of the slope is not fantastic i have many poop stuck on the slope instead of going into the collection bin area.

Here is some changes that i have made

-The gradient of the slope that the poop falls down from is greatly increased so poop should fall down ezier.

-The collection bin size have been almost doubled so it can collect much mre waste

-The drop zone after the downslope have been optimised so it can slide down mre efficiently and waste can accumulate properly.

-I have always love the slimness of this poop bucket so i have retained it slim profile and increase the capacity by extending it upwards instead.

Might not be suitable if you are using a rear spool holder originally from Bambu. This might block that holder at the back of the printer. Thank you.

Watch the difference in speed when the filament poop move down the slope.

What Mod / Fixes / Enhancement do i offer?

Please don't download the wrong one. Only those in the photos below is designed by me who painstakingly took a lot of time to measure carefully and design just to get it working. #SupportOriginal Love you guys for all the support so far!

- AMS FIX Failed To Retract Filament Error (a preventive measure and solve the bay 2 and 3 error and prevent bay 1 and 4 to have any possibility of having an error due to tension and friction) (Updated design on the 2nd photo below, try 1 then if it doesn't works properly for you then install the other one.)

(BRAND NEW) AMS Filament Pull Back Fix V2 Upgraded - Completely New Design Upgrade For AMS Filament Pull Back ERROR! Precisely Measured

- AMS Buffer Fix For Failed To Pull Back Filament Error (reduce wear on the external PTFE tube and allow the most smooth, least friction angle to go into the AMS buffer thus reducing the possibility of an error popping up)

- V2 AMS Buffer Fix For Failed To Pull Back Filament Error (reduce wear on the external PTFE tube and allow the most smooth, least friction angle to go into the AMS buffer thus reducing the possibility of an error popping up)

- AMS Fix - Stack the AMS on tp (Using a carefully measured holder to hold the PTFE in a curved angle that will allow filament to go through with the least possible amount of friction when the AMS is stacked on tp of the printer)

- AMS Buffer PTFE Right Guide Mount Fix will correct and maintain a nearly 100% straight line when the PTFE tube exit the AMS buffer to move into the printer extruder.

- V2 AMS Buffer Right PTFE Guide Mount - The Fix For Failed To Pull Back Filament a newly improved fix designed to replaced the V1 This will correct and maintain a nearly 100% straight line when the PTFE tube exit the AMS buffer to move into the printer extruder. Simple Installation. No screws needed!

- Extruder AMS Filament Pull Back Fix will correct and maintain a nearly 100% straight line to move the filament in and out of the extruder. This will also reducing wear on the PTFE tube. Its design allow the filament to travel in the most smooth, least amount of friction and pressure for the proper angle to go into and exit the extruder thus greatly reducing the possibility of an Failed To Retract Filament error or similar errors from popping up.

- V2 Extruder AMS Filament Pull Back Fix will correct and maintain a nearly 100% straight line to move the filament in and out of the extruder. This will also reducing wear on the PTFE tube. Its design allow the filament to travel in the most smooth, least amount of friction and pressure for the proper angle to go into and exit the extruder thus greatly reducing the possibility of an Failed To Retract Filament error or similar errors from popping up.

- The Smooth 4 Way Splitter. Look No Further. Combined with AMS Hub Lite together with this small attachment, you will have the Smooth 4 Way Splitter.