A1 Mini Pull Tray Purge Bucket Bin

Following the success of my Pull Out Poop Chute design for the P1P P1S X1C, here is my new version for the A1 Mini.

Highlights:

Easy to Print - Separated into 2 plates for easy print from Makerworld App

Large Size - reduce emptying frequency

Stability++ - The chute is being held to the side of the printer with 1 or 2 original screws under the printer

Pull Tray Design - Easy to empty chute

Non Purge Baffle Design - This chute do not use any Baffle and just a wall to let poop bounce off, my test shows that if a baffle is installed it may cause a significant amount to pile up the side, without the baffle the poop may pile up too but the movement of the arm will compress them down (without a baffle in the way) which is a + way to handle huge amount of poop like shown in the product photos.

However you can choose to attach a Baffle instead of the Deflector (Long Pink Plastic in photo) but i would think the deflector will work properly.

Please don't use silk material. Thank you.

Available on 2 versions.

Please choose carefully the version you want. Large or Smaller Version.

• If you own the P or X series or a large printer, you can choose the Large Version so it can store even waste before needing to empty the bin.
• If you own just the A1 mini, please choose the A1 Mini Smaller Version, Same design just smaller to fit the A1 Mini Bed

Installation Instructions:

Use a small philips screw driver or a small allen key poke through from the tp so the support inside the hole will come out easily

Proceed to remove the 1 or 2 screws from the bottom of the machine then put them through the 1 or 2 hole on the tray and screw it back in. It may NOT tighten but its ok.

Then take the Deflector piece (Pink in the below photo) and use a dab of glue and stick it at the side of the poop chute. Please don't use too much glue, may cause damage to the print walls and it wont be pretty anymore.

End product should look like this when done.

That is all. Enjoy your new large & convenient pull tray poop bin.

What Mod / Fixes / Enhancement do i offer?

Please don't download the wrong one. Only those in the photos below is designed by me who painstakingly took a lot of time to measure carefully and design just to get it working. #SupportOriginal Love you guys for all the support so far!

- AMS FIX Failed To Retract Filament Error (a preventive measure and solve the bay 2 and 3 error and prevent bay 1 and 4 to have any possibility of having an error due to tension and friction) (Updated design on the 2nd photo below, try 1 then if it doesn't works properly for you then install the other one.)

(BRAND NEW) AMS Filament Pull Back Fix V2 Upgraded - Completely New Design Upgrade For AMS Filament Pull Back ERROR! Precisely Measured

- AMS Buffer Fix For Failed To Pull Back Filament Error (reduce wear on the external PTFE tube and allow the most smooth, least friction angle to go into the AMS buffer thus reducing the possibility of an error popping up)

- V2 AMS Buffer Fix For Failed To Pull Back Filament Error (reduce wear on the external PTFE tube and allow the most smooth, least friction angle to go into the AMS buffer thus reducing the possibility of an error popping up)

- AMS Fix - Stack the AMS on tp (Using a carefully measured holder to hold the PTFE in a curved angle that will allow filament to go through with the least possible amount of friction when the AMS is stacked on tp of the printer)

- AMS Buffer PTFE Right Guide Mount Fix will correct and maintain a nearly 100% straight line when the PTFE tube exit the AMS buffer to move into the printer extruder.

- V2 AMS Buffer Right PTFE Guide Mount - The Fix For Failed To Pull Back Filament a newly improved fix designed to replaced the V1 This will correct and maintain a nearly 100% straight line when the PTFE tube exit the AMS buffer to move into the printer extruder. Easy Installation. No screws needed!

- Extruder AMS Filament Pull Back Fix will correct and maintain a nearly 100% straight line to move the filament in and out of the extruder. This will also reducing wear on the PTFE tube. Its design allow the filament to travel in the most smooth, least amount of friction and pressure for the proper angle to go into and exit the extruder thus greatly reducing the possibility of an Failed To Retract Filament error or similar errors from popping up.

- V2 Extruder AMS Filament Pull Back Fix will correct and maintain a nearly 100% straight line to move the filament in and out of the extruder. This will also reducing wear on the PTFE tube. Its design allow the filament to travel in the most smooth, least amount of friction and pressure for the proper angle to go into and exit the extruder thus greatly reducing the possibility of an Failed To Retract Filament error or similar errors from popping up.

- The Smooth 4 Way Splitter. Look No Further. Combined with AMS Hub Lite together with this small attachment, you will have the Smooth 4 Way Splitter.