MagSafe charging stand for iPhone (Standby mode)

Description

A Magsafe charging stand which allows for wireless charging of an iPhone and an Apple Watch or Airpods simultaneously.

Base and stand can easily be colored differently to your liking (separate objects).

Supports iPhone in vertical and horizontal MagSafe orientations
Apple Watch charger mounted below to charge Apple Watch or Airpod models which support charging on an Apple Watch charger (see compatibility below)
Fits newer Apple USB-C and older Apple USB-A chargers (see below)
Chargers with tight fit, but easily removable through holes
Integrated cable routing with optional cable clip for a clean on-desk look
Base, Stand and MagSafe cradle are separate objects, so you can easily choose different filament colors if you like

Tested with the following devices
- iPhone 16 Pro with/without Apple silicon case
- iPhone 15 with/without Apple silicon case
- iPhone 14 Pro with/without Apple silicon case
- Airpods 4 ANC version
- Airpods Pro 2
- Apple Watch Ultra 2
- Apple Watch 10 42mm
- Apple Watch 7 45mm
- Apple Watch 4 44mm
Tested with the following chargers
- Original Apple MagSafe 2020 charger
  - 15W “GEN 1”, plastic cable mantle
  - 55.9 mm in diameter
- Original Apple MagSafe 2024 charger
  - 25W “GEN 2”, braided cable mantle
  - 55.5 mm in diameter
- Original older Apple Watch charger
  - USB-A (2m), plastic cable mantle
  - 27.75 mm in diameter
- Original Apple Watch 2024 charger
  - USB-C (1m), braided cable mantle
  - 27.75 mm in diameter
NOT tested with
- iPhone Pro Max models
- iPhone Plus models
- Other iPhone cases
- Other chargers

Plate 01 “MagSafe iPhone charging stand”
- MagSafe 2020 cradle 56 mm inner diameter
- Charging stand with base (2 separate objects, can be colored individually)
- Watch charger puck 4 mm for older Apple Watch chargers
- (Optional) Cable plug and 1 spare
Plate 02 “MagSafe USB-C 2024”
- MagSafe 2024 cradle 55.6 mm inner diameter
Plate 03 “For Watch charger 2024”
- Watch charger puck 6 mm for 2024 Apple Watch charger

0.2 mm layer height, with variable layer height for the upper part of the stand.
- Found as good compromise between print time and quality during extensive tests.
- To save around 30 minutes of print time, you can turn “Ironing” off. Imo, those 30 minutes are worth it to get a really nice surface finish on the base of the charging stand.
15% Grid infill for good balance between filament use and sturdiness.
Only very small area with supports needed, easy removal.
If you don't want to print the optional parts (Cable plugs), simply select and drag them off the print plate.
Bambu Matte PLA (Ivory White and Ash Grey) was used for a lot of test prints and worked great. Your mileage (accuracy of fit) may vary.

Glue the MagSafe holder to the stand.
Put the MagSafe charger into the holder and route the cable through the stand.
Carefully insert the Apple Watch charger from below the base and route the cable to the back.
Use the puck (4 or 6 mm), to stabilize the charger from below. If needed, secure the puck with a small piece of adhesive tape.
Optionally, you can use one cable clip on the back of the stand to secure the MagSafe charger cable. As this is a quite small, fiddly part, please be aware, that this might break easily. You just need one of them, the second one is a spare part.
Just push it into place gently, once the cable was installed. If needed, you can pull it out with small pliers.
TIP: Depending on the surface the charging stand will be placed on, you could put a thin silicone pad or alike on the bottom of the base to minimize slip.

17.01.2025 MagSafe 2024 supported
- NEW part for 25W MagSafe 2024 “GEN 2” charger (braided cable mantle) included
- Updated description
- Split different print options to different plates
15.01.2025 Update of description posted
- MagSafe charger: Made for the USB-C one having the “plastic” cord
- Model update for MagSafe charger USB-C with “braided” cord will follow soon