Classic Frames – Switch | DISPLAY COLLECTION Free Model

Welcome to the very first release of our brand new Display Collection at Holoprops.

This collection is all about turning your game cases into real display pieces you can proudly hang on your wall and swap in seconds depending on what you are playing, collecting, or vibing with.

We are kicking things off with a free model, simple, clean, and super functional:

👉 Switch Classic Frames

Compatible with Nintendo Switch 1 and Switch 2 game cases.

It is a timeless rectangular frame, designed to blend into any setup.

Three different variations are included, so you can choose the one that fits your space best.

All magnets across the entire Display Collection are always the same size: 10 mm x 3 mm.

We actually recommend buying a large pack of magnets so you are fully set for everything coming next.

After testing many different brands, the strongest magnets we found are from Bambu Store Maker Supplies, but you can find these magnets easily on Amazon or AliExpress as well.

🧲 Magnetic Wall System - Simple, Clean, Future-Proof

The Wall Mount is included for free, and most importantly, it is fully standardized across the entire Display Collection.

That means:

One Wall Mount will work with all future frames and accessories we release in this collection.

Wall installation is simple:

• Uses 2 screws

• Drywall requires anchors

• Wood studs can use wood screws

• A drilling template is included so everything stays perfectly aligned and levelled.

Inside the Wall Mount, you will glue 2 standard round magnets: 10 mm x 3 mm.

⚠ Very important

Both magnets inside the Wall Mount must be glued with the same polarity and always in the same direction on every mount you install.

The two rear magnets of a frame must always be installed with matching polarity to work correctly with any Wall Mount.

The same rule applies to the badge system: glue the corner magnet with the same polarity and in the same direction on every frame, and always match that polarity when installing the magnet inside your badge or accessory.

This simple rule is what makes the whole system work perfectly, so you can swap your frames instantly, anywhere, anytime.

🧲 Magnets Inside the Frame + Badge System

Each Switch Frame Classic includes:

• 2 rear magnets for wall mounting

• 1 extra corner magnet for future badges and decorative accessories

Always install both rear magnets with the correct polarity on every frame so they remain compatible with all your Wall Mounts. Polarity is critical for the system to work properly.

Magnets are glued with:

• A small drop of super glue

• Press firmly into place

• Let the glue fully cure before mounting

On our side, we use a super glue accelerator so the bond sets in just a few seconds.

⚠ Again, polarity matters

If the polarity is wrong, the frame or future badges will not attach correctly.

🖐 Easy Removal From the Wall

Removing the frame takes literally one second:

• Grab it from the bottom

• Gently pull it toward you

  ➡ It naturally detaches from the magnets without force

🖨 Optimized Printing and Premium Finish

All three frame variants are printed at a 35-degree angle for the cleanest surface possible.

The included 3MF file is fully pre-configured, with:

• Optimized supports

• Strategic orientation

• Clean surfaces

• Easy support removal

• Strong but material-efficient settings

We spent days inside Bambu Studio documentation and testing dozens of prototypes to dial this in perfectly. So please, use the 3MF file provided.

Each frame prints in about 3 hours, making it a fast and satisfying print.

For best results, we always recommend:

• A clean build plate, washed with warm water and mild dish soap, Air-dried

• A fully functional printer with a not too old plate or nozzle.

• And using our 3MF file exactly as provided

This ensures perfect adhesion and the cleanest possible finish.

🎯 Perfect Fit for Switch 1 and Switch 2 Game Cases

We carefully engineered the internal fit so that:

• Both Switch 1 and Switch 2 cases fit perfectly

• The cases slide in easily

• And nothing gets damaged or scratched

🎨 Printing Details:

• Nozzle: 0.4 mm

• Layer Height: 0.2 mm

• Infill: Hatch (8%) or Cubic (15%)

• Supports: Yes! Supports are perfectly calibrated in the 3MF file.

• Walls: 2

3MF files Ready to print out-of-the-box

We've fine-tuned countless custom settings ➡ infill, speed, bridges, seams, and more. Hours of research in slicer wikis go into every file to give our Patreon supporters the best plug-and-play experience.

The included 3MF files are optimized for Bambu Studio and should work correctly with Orca Slicer and Prusa Slicer. Using them in other slicers may break alignment, colors and custom settings.

Join the conversation

We’d love to see your prints! Share them on our Holoprops Discord and connect with the community.

Licensing

All Holoprops models are 100% original creations, hand-sculpted with care and creativity.

These models are our own intellectual property and are protected accordingly.

Personal use only. For commercial rights, join our Merchant Tier:

• Patreon Merchant Tier

Filaments used

All filament from the Polymaker Store.

(This is an affiliate link, and if you decide to grab a roll, we get a tiny thank-you in return. We really appreciate your support!)