Illusion Windturbine TIE F. Tail Fin

Thanks to cooasty for the beautiful pinwheel.
The two propellers are counter-rotating and have a nice "hypnotic" effect due to their shape. After cooasty's windmill had survived a few years and storms, I wanted to build the windmill bigger and with ball bearings. I inserted a hub with a bearing seat for a 608 ZZ ball bearing into the propeller. The propellers sit on an M8 stainless steel threaded rod. With fuselage, the threaded rod (length 122 mm) is pushed through and held in place with a nut at the back. Five different tail fins can be fitted. I first wanted to do the vertical axis with a ball bearing (it's still possible), then I used an 8 mm round steel bearing with a tip, it works perfectly. The two labyrinth rings are centered at the rear of the propellers with LabyrinthZent and glued with CA. Drill out the small holes on the propellers with 2.5 mm, then you can simply screw in an M3 screw. The vertical axis is inserted into the bottom of the fuselage, the 8 mm inner diameter must be able to rotate easily on the 8 mm rod. To do this, adjust the vertical axis with a test print with "Horizontal expansion" and "Horizontal hole expansion". The 8 mm rod must sit tight in the vertical holder, the VertikalHalter16x8 fits on a 16 mm rod / tube. VertikalHalter0Z5x8 fits a 1/2" water pipe. Tail fin Tie, heart, 120 and 130 are glued to the respective carrier with CA. For Propeller250 you need at least a 250x250 mm printer, for Propeller200 200x200 print area is enough. The 2PropOM propellers have no mouse ears.

Are needed:
2x ball bearings 608 ZZ for propellers
6x cylinder screw M3x12 for propeller (3 per propeller are enough)
1 threaded rod M8x93 or M8x122 with nut and self-locking nut for propeller
2x cylinder screw M4x12 with nut for tail fin
1x cylinder screw M4x20 with nut for the rear
1x stainless steel or brass rod 8x100 for vertical axis
1x stainless steel or brass rod 8x12 with tip for vertical axis

Assembling the propellers see picture
M8 threaded rod
M8 nut
Distanz5
PropellerLi with Labyrinthring, bearing and Deckel
Buchse16
Buchse12
PropellerRe with Labyrinthring and bearing
Distanz2
2 M8 Nut or Self-Locking Nut
Spinner

I printed all the wind turbines with PLA. I recommend brighter PLA up to 35°C air temperature. If it is warmer or if darker filament should be used, then use PETG or better ASA.

I would be happy about a make or remix...

I would also like to recommend these wind turbines:

Illusion Windturbine MK2 counter-rotating

https://www.printables.com/de/model/895957-illusion-windturbine-mk2

Double rotor addon for wind turbine MK2

https://www.printables.com/de/model/887565-double-rotor-addon-for-wind-turbine-mk2

Double wind turbine MK3 counter rotating

https://www.printables.com/de/model/883528-double-wind-turbine-mk3-counter-rotating

Wind Turbine MK3 neo Remix

https://www.printables.com/de/model/882595-wind-turbine-mk3-neo-remix

Archimedes Wind Turbine Remix

https://www.printables.com/de/model/773350-archimedes-wind-turbine-remix

Ugrinsky Vertical Axis Wind Turbine Remix 

https://www.printables.com/de/model/769216-ugrinsky-vertical-axis-wind-turbine-remix

Mini Airplane Wind Turbine

https://www.printables.com/de/model/643163-mini-airplane-wind-turbine

Savonius Vertical Wind Turbine Remix 

https://www.printables.com/de/model/775074-savonius-vertical-wind-turbine-remix

Darrieus Savonius Turbine Ver.2 Remix 

https://www.printables.com/de/model/776180-darrieus-savonius-turbine-ver2-remix

Windturbine MK2 neo Remix

https://www.printables.com/de/model/782829-windturbine-mk2-neo-remix

Illusion Windturbine 200 / 250

https://www.printables.com/de/model/785427-illusion-windturbine-200-250

Toroidal Illusion Windturbine 

https://www.printables.com/de/model/790615-toroidal-illusion-windturbine

Wind Turbine 620 mm

https://www.printables.com/de/model/810511-wind-turbine-620-mm

Wind turbine savoniov helix – Remix

https://www.printables.com/de/model/843331-wind-turbine-savoniov-helix-remix