May 29, 2025
Description
Original description:
This is the 2nd version (v2.0) Gridfinity Bins with lids. All bins are 6U tall and this set includes the following types (see image below):
The bins included here are similar to the version 1.0, but have the following changes or improvements:
The following attributes were carried over from the version 1.0 models:
To assemble the doors, I used a couple medium paperclips (mine had a wire diameter of about 0.85mm and 1.05mm). I first straightened them so they can be used as hinge pins for the doors. The thinner paperclip wires will be easier to assemble, but I was able to use the thicker 1.05mm diameter paperclips. However great care must be taken, especially with the larger paperclip wires, since they require more force to insert thicker wires (I used a pliers to install the larger wires).
To avoid a nasty poke if the hinge wire were to burst through the doors or the other side of the bin, if using too much force, do NOT press the hinge wires in place if your hand or other body part is on the other side. The hinge wires do not go all the way through, there is about 1mm of plastic which stops the wire from going through. If you press too hard while installing the wires, it could bust through that 1mm wall, and pop out the other side - and you don't want your hand in the way of that wire, if it were to pop through during installation.
To install the doors, the paperclip wire was inserted from one side on the 1x1 and 1x2 bins, and threaded through the doors until it stopped (the wire only feeds from one side of the bin with the hole in it).
For the 1x4 bin, the wire goes in through both sides, into each door, until it stops (the wire will only go about 16mm). I used pliers to insert the wires, since they are a snug fit with the holes. A drop of superglue can be used on the end of the wire, however I have not had to use that on my bins.
When I installed the wires, I first seated them, and then backed them out a mm before flush cutting them off. Then I would press the wires below the surface of the bins, so they did not protrude.
You can use the included 3MF (BambuStudio) which has all the files set up for printing.
If you want to set the files up in your own slicer, here are some tips that may help. Note that the files are not oriented for printing so some parts will need to be rotated to print without supports. If you intend to print the lids in one color, you can use the files named:
For the 1x1 single compartment bins:
For the 1x2 three compartment bins:
For the 1x4 six compartment bins:
If you want to print the tabs in a different color, then use the files listed below (load both together into the slicer together so they maintain their orientation). The tabs use an integrated hinge, so they need to print with the door (so load them into the slicer together). This way they are split into two models (tab and door) for multicolor printing (which makes coloring much simpler in the slicer).
For Multicolor printing only:
Load these into the slicer together:
For the 1x1 single compartment bins:
For the 1x2 three compartment bins:
For the 1x4 six compartment bins:
In Orcaslicer (others should be similar), you can load two or more objects together by dropping them together on the build plate and answering “yes” when it askes if you want to load the files as a single object. Doing this will maintain the orientation of the door and tabs which is required for them to print correctly.
Other stuff:
There are similar multi compartment latching lid bins available at the links below:
Gridfinity 1x1 Bins with Latching Lids v1.0
Gridfinity 1x2 Bins with Latching Lids v1.0
Gridfinity 1x3 Bins with Latching Lids v1.0
Gridfinity 1x4 Bins with Latching Lids v1.0
Gridfinity 2x2 Bins with Latching Lids v1.0
Gridfinity 2x3 Bins with Latching Lids v1.0
If you need some bins for small parts, the following bins with covers are a good option to use with the Box For Stuff 20 bin and 25 bin cases (or other 6U tall cases):
If you want to check out my other Gridfinity cases, you can find them at the links below:
If you want to store some small hardware and need some good labeled bins, Ch3vr0n posted some segmented bins for the Gridfinity system here:
https://www.printables.com/model/732655-gridfinity-boxes-for-gridfinity-box-for-stuff-20-b
There are currently no authorized sellers of prints of this model or prints of this model.
Thanks and Acknowledgements:
The models here could not have been made without the work of Zach Freedman, who introduced the world to Gridfinity, and then set it free for everyone to use. These models are not based on direct remixing of Zach' original models, but they are fully compatible, and use the same, or a similar specification for the bin bases, bin lips and base grids, which Zach Freedman developed. Zach Freedman's work is available on Thangs, and you can find examples of his Gridfinity designs here and here, which are available under his MIT license. If you like this model, or want to learn more about Gridfinity, you can check out Zach Freedman's YouTube, or you can support Zach Freedman's work on Patreon (patreon.com/zackfreedman).
And Finally,
If you find these models useful, please post a like or a comment with some pics of your prints.
You can find the other things I'm working on at my blog here. You can also follow me here on Printables or over at MakerWorld, to see what new stuff I post. If you would like to support my work, you can Buy Me A Coffee using this link:
https://www.buymeacoffee.com/mystoopidstuff
Thanks for looking!
Changelog:
Update 3/31/2024 - Thanks to a comment on Reddit, I'm gonna make a filament hinge version of these, which should be posted next week.
License:
Standard Digital File License
8
MyStoopidStuff
