Worker Dominator Lipo Power Stock

This is a Worker Dominator ONLY adjustable lipo Stock ... The internal space is about 50x 50x 120mm . BUT i can make it longer on request since we need, like 5000mah + For the Dominator .. and the stock battery box is the usual joke.

There is also a Large version which is 50mm Wide x 55mm Deep x 146 Long. It is intended for 5000Mah batteries.

Moving the battery back beyond the grip also helps to counter the weight of the motors and helps to balance the blaster out. AND certainly looks better than a hideous lipo hanging off the side.

You can connect power via the back of the stock attachment point OR into the back of the existing battery box (which i prefer)

Battery selection...
Assuming you have a single stage Ultra Stryfe now, and you have a 3s 1500mah battery (This is smaller than i would ever run) and you're happy with that, then if you go form 1 stage to 3 stages you'll need 3 times the capacity for the same run time .. so 4500mah..

But it's unlikely you'll stop at 3s as you'll be limited by RPM and the 3rd stage probably wont be doing anything ... If you bump them all to 4's that's 33% more voltage and current so you'll need a battery 33% bigger or .. 6000mah..

This is why you need a stock like this .. irrelevant of if you are running Brushless or not..

Worker Swordfish stock here
https://www.thingiverse.com/thing:3275419

Website
Http://Ultrasonic2.com

Facebook Group
https://www.facebook.com/groups/MakingStuffAwesome/

**** Why you should support me on Patreon ****
https://www.patreon.com/Ultrasonic2

Shop
https://www.etsy.com/listing/571034709/ultrastryfe-brushless-motor-cage-by

The stock is adjustable via m3 thumb screws (different than shown) on 10mmx8mm carbon fiber rods ( 8mm painted rods shown )
Painted rods are shown because it will take more than a month for the real carbon rods to ship to me and i just couldn't wait that long before sharing it with you .. i'll update the pics once i get them.

It's expected that you'll glue the rods into the Butt and end caps.

The stock has place for two additional "support" screws and i strongly suggest you pre drill these holes and use these screws to help to support the weight of the lipo hanging off the back

Print the battery box with the attachment point on the bed .. with supports over 89 degrees .. This means no supports are required for that back of the box .. which is then printed at a 80 degrees angle which i had not problems with but i do have ALOT of part cooling.

I printed the Butt with a 10 degrees angle so it sat flat on the print bed .. without supports other than over 89 degrees ... This also requires significant part cooling.

I printed the box lid upside down .. and came out just fine with good cooling.

The Licnence you agree to when downloading this thing prevents you from making a profit from MY thing. This means you CAN NOT sell this or any of my other things on places like Ebay, Facebook, Forums or Etsy. You also may Not sell My parts as Part of a complete blaster. I don't profit from putting this thing us as a Free download and therefore no one else should too.

Parts

M3 Nuts x3

M3 Thumb screws
8mm long x3 (at least one needs to be low profile. Not like the pictured ones)
Aliexpress
http://s.click.aliexpress.com/e/cqbAApHW
Amazon
https://www.amazon.com/s/ref=as_li_ss_tl?url=search-alias=aps&field-keywords=M3+Thumb+screws+&linkCode=sl2&tag=ultrasonic206-20&linkId=01191aa3f42b9fc0ca31476b5673c8ed&language=en_US

M3 self tapping counter sunk screws
8mm x3
20mm x1
Aliexpress
http://s.click.aliexpress.com/e/9kpNSMu
Amazon
https://www.amazon.com/s/ref=as_li_ss_tl?url=search-alias=aps&field-keywords=M3+Thumb+screws+&linkCode=sl2&tag=ultrasonic206-20&linkId=01191aa3f42b9fc0ca31476b5673c8ed&language=en_US

Attachment catch spring
dia 0.4mm D5mm L 15mm
http://s.click.aliexpress.com/e/belUCD2o

Carbon Fiber rods .. 10x8mm or solid 10 mm length 340mm or longer (i would suggest you get glossy carbon fiber because it looks awesome !)
Aliexpress
http://s.click.aliexpress.com/e/XsxqN7i
Amazon
https://www.amazon.com/s/ref=as_li_ss_tl?url=search-alias=aps&field-keywords=M3+Thumb+screws+&linkCode=sl2&tag=ultrasonic206-20&linkId=01191aa3f42b9fc0ca31476b5673c8ed&language=en_US

Battery Turnigy Graphene Panther
Amazon
https://www.amazon.com/s/ref=as_li_ss_tl?url=search-alias=aps&field-keywords=M3+Thumb+screws+&linkCode=sl2&tag=ultrasonic206-20&linkId=01191aa3f42b9fc0ca31476b5673c8ed&language=en_US

HobbyKing
https://hobbyking.com/en_us/graphene-2200mah-3s-75c.html?affiliate_code=NWMBPALUPSESFPQ&_asc=1313262664

AliExpress
http://s.click.aliexpress.com/e/ciythXoy

GearBest
https://www.gearbest.com/3s-65c-lipo-2200mah-_gear/?lkid=19775127

BangGood
https://www.banggood.com/custlink/m3vDdo4uJv

Update 12/Dec/2018
Changed stock rod holes to 10.5mm
Changed Butt rod holes to 10.4mm

Update 13/Dec/2018
Updated catch and door

Update 19/Dec/2018
Updated door and catch for door on the stock

05/Jan/2019
Added alternate rod end
Improved aesthetics of the catch
Added a larger battery box for 5000mah batteries