Ardumower Arctic Hare mod by Jussi

This is a remix of raess Ardumower Arctic Hare design.

Most of the parts are printable without supports and some will need supports but less than original. Parts are stronger and lot of little things are changed here and there. Should be more waterproof etc. Probably none of these parts can be mixed with original design parts. Biggest change is added cover for cutting blades.

Charging station is my own design. Station contacts are 20x20 U-shaped aluminium extrusion with springs. Mower contacts are made from 12 mm copper capillary end caps and theres magnets inside to ensure contact.

I printed all mower parts with devil design ASA except wheel surfaces, those are TPU.
These parts are made for prusa mk2 printer, so these are bigger than originals. All except wheel surfaces are printable 250x210x200 building space, wheel surfaces diameter is 218mm.

Electronics, motors, blades etc. are kit from Marotronics (this kit contains a lot of stuff):
https://www.marotronics.de/Elektronik-Set-fuer-den-Rasenroboter-aus-dem-3D-Drucker

Battery pack casing is N.E.S.E module. Printed them on PETG. N.E.S.E module models and parts can be found here http://18650.lt/
Cells: Samsung 35E 18650 3500mAh
BMS: 7S 24V 20A Protection Board Charging Controller TE992

Other parts used:
Rain Sensor: FC-37 or YL-83
Temperature & humidity: DHT22
NEO-6M GPS module
GY-801 imu module
Waterproof ultrasonic sensors: JSN-SR04T
Bumper: EPDM foam rubber D-profile SK 21x17 mm
BumperDuino board: https://www.marotronics.de/Bumper-Duino-Dual-Drucksensor-Board-zB-fuer-Arduino-Raspberry-pi
Raspberry Pi Zero w, zero camera and 18 x 1,2 mm round glass
Raspberry Pi 3b+
24VDC/5VDC 5A step down buck for raspberry pi's
M12 cable glands
M3, M4 and M5 A2 stainless screws, washers, nylon nuts and square nuts.
2,5 mm silicone rubber cord to drive motors lid gasket
Power connectors: IP68 SP13 Waterproof Aviation Plug Socket Connector 2 pin
USB socket: CONEC 17-250021 Socket; USB B mini
Front wheel shaft can be made from stainless 8 mm threaded rod and nylon nuts
Bearings for front wheel 688-2RS
Sanitary silicone between parts for waterproofing
3 mm aluminium tig welding rod for pcb box lid hinge
250m perimeter wire
10 Ohm 50 W power resistor for perimeter wire circuit

Filament usage around 11kg ASA and 0,8kg TPU.
Printing time around 600h with 0.6 nozzle and E3D Volcano hotend.

Software: Ardumower - The Do-It-Yourself Lawnmower Robot https://www.ardumower.de/index.php/de/

Github: https://github.com/jussipu/AzuritBer

My building topic: https://forum.ardumower.de/threads/arctic-hare-mod-by-jussi.23557/

UPDATE: 24.4.2019
Step-file is now uploaded, assembly part names are partly finnish, swedish and english :) you have deal with that.

UPDATE: 30.4.2019
Mower is now completed. Some pictures and testing video uploaded.
https://youtu.be/zPInJqTAmYc

UPDATE: 4.5.2019
Parts what I used is now listed to description.
Next thing to do is perimeter wire installation and some kind of shelter for charging station and mower.

UPDATE: 8.9.2019
Video added, mower drives smooth with IMU and odometry. EPDM foam rubber bumper was too sensitive. Garden hose work much better. Center u.s. sensor is too low, it can't be used at all. Otherwise it's has been worked as expected. I have some upgrades coming during winter. Wlan antenna, more bumper hose, u.s. sensors to new positions etc. minor things