This is a set of walls for use with my MagHex Tile System for Gloomhaven. These walls have magnets and wire nail holes in strategic locations that allow you to securely place them on the MagHex center mag tiles.
###Features
There are wall sections to work as both "flat to flat" and "point to point" so you should be able to build every scenario in the book. (Untested)
Want doors for your scenario? Check out MagHex Doors that work with this system.
Three ways to use MagWalls with MagHex Tiles:
Press fit 3x3mm neodymium magnets into slots on the bottom of the wall segments. It's a friction tight fit and requires no glue.
Press #19 x 1/2" Wire Nails into recessed holes on the bottom of the wall segments. a.(Nail dimensions: 13.5mm long; 2.2mm diameter head; .5mm thick head; 1.1mm diameter shaft)
Glue MagWall segments to MagHex Blank or Terrain tiles.
###Notes
MagWall sections come in 3 types:
F type - Used on Flat to Flat sections of terrain
P type - Used on Point to Point sections of terrain
C type - Used to link sections together at a corner
MagWalls use 3x3mm neodymium magnets that you can buy in bulk from ali express or ebay.
The polarity of the magnets needs to all face the same direction and match the polarity of the center magnets used in the center mag bases.
The wire nails can be bought in large packs for very little ($1.50) from any home improvement store. (Home Depot, Lowes, Ace, etc.)
Some wire nails will have to be cut shorter so they wont extend out the top of the model.
These walls are under construction! Proceed at your own peril! (hehe)
###Changelog 04.23.2020
Added Ashlar C4 corner wall. Thanks for the idea bshigenaka!
03.17.2020
Added Ashlar F4 wall
09.22.2019
Added 2 more Wood walls per Nephilim2001's request.
06.12.2019
Added 3 more Ashlar walls.
06.10.2019
Updated the Ashlar wall type with a deeper texture. The test print didn't have enough definition to paint easily.
06.08.2019
Added a new type of wall! Ashlar! It's similar to Cobble, only not ruined. There are 8 pieces to try when you're building your next scenario!
Added Forest Grass wall. Print at .4 layer height, 100% infill. Cut away the cylinder. Press magnet in first, then use a blow dryer to shape the strands. Thanks to RobagoN for the idea!
05.30.2019
Made 3 new Wood wall segments
05.27.2019
Made 11 Stone walls segments! These have a cavern like appearance that looks very similar to the original tile art.
Added 4 Forest themed wall segments. The giant mushroom has to be printed in two parts and then glued together. I want to make more forest themed things, but I'm fresh out of ideas. Please post a comment with suggestions!
05.25.2019
Split MagHex Doors into their own thing to reduce clutter
05.20.2019
Added 2 Cobble Doors. Went with a metal look for the door itself, but I may also add a wood looking option as well.
05.19.2019
Added 2 Wood Doors! This took a lot more time and effort than I expected, but I think they turned out lovely. These are obviously heavily inspired by Rbross' door design.
05.18.2019
Added 2 Cobble wall segments
05.16.2019
Modified the wood corner segments to work a bit better
05.15.2019
Added 4 Wood Corners
Added 2 Wood Walls
Changed Naming Scheme to better reflect where/how a wall section should be used
05.12.2019
Added 3 Cobble Corners
05.11.2019
Updated design of the magnet slot with a slope to make it easier to insert
After tested with earring posts, I found out that they did not offer enough magnetism.
Switched all earring posts with wire nails
Changed magnet and wire nail intervals to better align with MagHex Bases
Reduced width of cobblestone wall segments (save filament and take up less space)
Added some texture to the plaster areas of the wood wall segments
Added 2-tile wood wall segment
05.09.2019
Updated design to use earring flat posts
Added 1 wood design
05.05.2019
Uploaded the first batch of Cobblestone walls. More to follow...
Xevin
