#1:48 ESA ATV Model Building Instructions
These files form a 1:48 model of the ESA Automated Transfer Vehicle (ATC) for 3d-printing. The model is divided into several subassemblies. It is recommended to print all parts from PLA. All files can be printed without support unless otherwise noted.
# THruster Bay (THB)
| Part: | Color: | Qty.: |
|:----------------------------:|:------------:|:-----:|
| ATV_THB_shell_wh.stl | White | 1 |
| ATV_THB_cone_white.stl | White | 1 |
| ATV_THB_antenne_base_wh.stl | White | 1 |
| ATV_main_trusters_wh_gy.stl | White/Black* | 4 |
| ATV_EPM_nose_antenna1_wh.stl | White | 1 |
| Magnet (6x2mm) | - | 6 |
\* Mid-Print Color Change
# Solar Panels
| Part: | Color: | Qty.: |
|:-----------------------------:|:------:|:-----:|
| ATV_solar_array_connector.stl | Grey | 4 |
| ATV_solar_array_frame_gy.stl | Grey | 4 |
| ATV_solar_panel_bl.stl | Blue | 16 |
| Magnet (6x2mm) | - | 4 |
# Equipped Propulsion Bay (EPB)
| Part: | Color: | Qty.: | |
|:-------------------------------------:|:------:|:-----:|-------------------|
| ATV_EFB_propellant_tank_bottom_bk.stl | Black | 8 | |
| ATV_EFB_propellant_tank_top_bk.stl | Black | 8 | |
| ATV_EFB_shell_wh.stl | White | 1 | |
| ATV_EFB_tank_frame_gy.stl | Grey | 2 | |
| ATV_thruster_block_gy.stl | Grey | 4 | (Supports needed) |
| Magnet (6x2mm) | - | 16 | |
\* In my case I had to stacked multiple magnets inside to be able to hold the solar panels.
# Equipped External Bay (EEB)
| Part: | Color: | Qty.: |
|:--------------------------------:|:------:|:-----:|
| ATV_EEB_gas_tank_bottom_bk.stl | Black | 7 |
| ATV_EEB_gas_tank_top_bk | Black | 7 |
| ATV_EEB_shell_wh.stl | White | 1 |
| ATV_EEB_tank_frame_gy.stl | Grey | 1 |
| ATV_EEB_water_tank_bottom_bk.stl | Black | 3 |
| ATV_EEB_water_tank_top_bk.stl | Black | 3 |
| Magnet (6x2mm) | - | 5 |
# Equipped Avionics Bay (EAB)
| Part: | Color: | Qty.: |
|:--------------------------------:|:------:|:-----:|
| EEB | - | 1 |
| ATV_EAB_shell_wh.stl | White | 1 |
| Magnet (6x2mm) | - | 6 |
Equipped Pressurized Module (EPM)
| Part: | Color: | Qty.: |
|:----------------------------------:|:------:|:-----:|
| ATV_EPM_bag_big_wh.stl | White | 24 |
| ATV_EPM_bag_small_wh.stl | White | 36 |
| ATV_EPM_bottom_cone_wh.stl | White | 1 |
| ATV_EPM_interior_base_plate_gy.stl | Grey | 1 |
| ATV_EPM_nose_antenna1_wh.stl | White | 1 |
| ATV_EEB_antenna_wh.stl | White | 1 |
| ATV_EPM_rack_gy.stl | Grey | 4 |
| ATV_EPM_shell_wh.stl | White | 1 |
| Magnet (6x2mm) | - | 9 |
# Nose
| Part: | Color: | Qty.: |
|:----------------------------------:|:------:|:-----:|
| ATV_EPM_nose_antenna1_wh.stl | White | 1 |
| ATV_EPM_nose_base_wh.stl | White | 1 |
| ATV_EPM_nose_camera_bk.stl | Black | 2 |
| ATV_EPM_nose_cone_bk.stl | Black | 1 |
| ATV_EPM_nose_docking_system_bk.stl | Black | 2 |
| ATV_EPM_nose_seal_bk.stl | Black | 1 |
| ATV_EPM_nose_seal_ring_gy.stl | Grey | 1 |
| ATV_EPM_nose_star_tracker_bk.stl | Black | 2 |
| ATV_EPM_thruster_gy.stl | Grey | 4 |
| Magnet (6x2mm) | - | 4 |
# Stand
| Part: | Color: | Qty.: | |
|:------------------------------------------:|:------:|:-----:|:----------------:|
| ATV_stand_bracket_wh.stl | White | 1 | (Support needed) |
| ATV_Stand_Rod.stl | White | 1 | |
| M3 Nut | - | 1 | |
| M3 Washer | - | 1 | |
| IKEA APTITLIG (24x15cm) Wood Butting Board | - | 1 | |
# 3D-PDF
The attached PDF is a 3D-PDF and can help for the assembly. Adobe Acrobat is needed to open the PDF and you need to trust the file in Adobe Reader to enable the 3D-function.Therafter klick on the red question mark.
License:
Creative Commons - Attribution - Non-Commercial
CatSailer1279
