VMO MASK V3 - 3D-PRINTED PROTECTIVE - CORONAVIRUS COVID-19 (IMPROVED VERSION)

VMO MASK V3, Mar 2020 (Improved Version)

3D Printed Mask reusable with filter

My WEB:
https://saferfacemask.co.uk/

If you want to join me to my fight against COVID-19, be my patreon (Si quieres unirte a mi lucha contra COVID-19, sé mi patreon):

https://www.patreon.com/user?u=32471655

INSTRUCTIONS: (Instrucciones):
https://youtu.be/bpcbeetAats
https://www.youtube.com/watch?v=lrQWaV4bhJ8&feature=youtu.be

01 APRIL 2020:
New Coupler V3 (P1).stl
Installed from inside, easy to print, need to be glued using SUPER GLUE after install
(Instalado desde el interior, fácil de imprimir, debe pegarse con SUPER GLUE después de la instalación)

It requires the use of 8 cm diameter HEPA/N95 filter

As an alternative, one or more disposable surgical type filters can be cut to make a simple filter, but to be used in low risk situations.

At least two or three layers of Plastic PRIMER should be applied on the outside of the mask to reduce the possibility of entry of the virus, which can penetrate the plastic (PLA or PETG), lets dry 24 Hours.

This is my first contribution against the fight against the coronavirus COVID-19, and I will continue working to improve the design and develop other products. If you require any special filter measure, please leave me a comment, for new designs

It is a PROTOTYPE, and no scientific studies have been carried out, but it contributes to reducing the entry of the COVID-19 virus, depending on the filter used, and most importantly, it contributes to reducing the viral load, using it at will.

---

Mascara de protección re-utilizable

Se requiere utilizar un filtro 8 cm de diámetro tipo HEPA/N95

Como alternativa, se puede recortar uno o varios filtros desechable tipo quirúrgico, para fabricar un filtro simple, pero de uso en situaciones de poco riesgo.

Se deben aplicar de dos o tres capas, como mínimo, de PRIMER para plasticos por la parte externa de la mascara para reducir la posibilidad de entrada del virus, el cual puede atravesar el plástico (PLA o PETG), dejar secar 24 horas.

El porta filtro es removible y puede ser sustituido por otros modelos con anclaje tipo 3M.
(The filter holder is removable and can be replaced by other models , fit some 3M filters)

Este es mi primer aporte contra la lucha contra el coronavirus COVID-19, y seguiré trabajando para mejorar el diseño y elaborar otros productos. Si requiere aluna medida especial de filtro, déjeme un comentario, para nuevos diseños.

Es un PROTOTIPO, y no se han realizado estudios científicos, pero contribuye a reducir la entrada del virus COVID-19, dependiendo del filtro utilizado, y lo mas importante contribuye a reducir la carga viral, usar a discreción.

---

PRINT (Imprimir):

I recommend doing the Horizontal Expansion Test, to verify if the printer is correctly calibrated, before printing the parts

Recomiendo hacer el Test de Expansión Horizontal, para verificar si la impresora esta correctamente calibrada, antes de imprimir las piezas.

TEST:
HorizontalExp.stl

MASK:
VMO Mask V3 (P).stl
Coupler V3 (P).stl or Coupler V3 (P1).stl
FILTER B(P).stl
FILTER Cap(P).stl
Valve-A (Rosca).stl x 2
Valve-B.stl x2

Elastic Cord (Cuerda Elástica)
S-C.stl x 2

Opción 1 (Option 1): PIN
A-PIN.stl x 4
B-PIN.stl x4
Sin Tornillos (No screw) – usar (use) Super Glue

Opción 2 (Option 2): Tornillos (Screw) M2
A-M2.stl x 4
B-M2.stl x4
Tornillos (Screw): M2x8mm x4

Opción 3 (Option 3): Tornillo (Screw) M3
A-M3.stl x 4
B-M3.stl x4
Tornillos (Screw): M3x8mm x4

NEED (Se necesita)
Two 10mm x 40cm elastic cords (Dos elásticos de 10mm x 40cm)
O Ring D:20mm
Rubber Strip (Tira de Goma): 36,5 cm
Remove the bottom of the rubber, and glue with Super Glue
(Quitar la parte inferior de la goma, y pegar con Super Glue)

Felpa (Felt): D: 38mm with center hole D: 12mm
Plastico (Plastic): D:30mm 50 micron (0.05mm)
Used to do Plastic Punched Pocket Folders

https://www.amazon.co.uk/Quality-Plastic-Punched-Pockets-Folders/dp/B07B9BDD9T/ref=sr_1_2_sspa?crid=29JRWWFKB5UTZ&dchild=1&keywords=punch+pockets+a4&qid=1585506496&sprefix=Punch+pocket%2Caps%2C172&sr=8-2-spons&psc=1&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUEzSFU0OVFWQVJHQVk2JmVuY3J5cHRlZElkPUEwNTMwMDgzMkxFNjRYTDhUWTFNTCZlbmNyeXB0ZWRBZElkPUEwODE3NzEyMjY4VFdWVkY2MFczRyZ3aWRnZXROYW1lPXNwX2F0ZiZhY3Rpb249Y2xpY2tSZWRpcmVjdCZkb05vdExvZ0NsaWNrPXRydWU=

VIDEOS:

FILTER AIRFLOW: https://youtu.be/sOg0Ax_Mlh8
FILTER TEST: https://youtu.be/lrQWaV4bhJ8
MASK SEAL: https://youtu.be/bpcbeetAats
VISOR: https://youtu.be/gi7PAh1TBmY

DESIGNS (Diseños)

https://cults3d.com/en/users/victorottati/creations

VISOR V1:
https://www.thingiverse.com/thing:4244384
https://cults3d.com/en/3d-model/various/vmo-visor-v4-15gr-3d-printed-shield-coronavirus-
covid-19
DECATHLON MASK ADAPTOR (Adaptador Mascara) 
https://www.thingiverse.com/thing:4279946
https://cults3d.com/en/3d-model/various/vmo-decathlon-mask-adaptor-and-fit-3m-filter-3d-
printed-protective-coronavirus-covid-19
MASK V3 (Mascara V3):
https://www.thingiverse.com/thing:4251943
https://cults3d.com/en/3d-model/various/vmo-mask-v3-coronavirus-covid-19-improved-
version
https://www.myminifactory.com/object/3d-print-117089
SURGICAL MASK STRAP (Tensor para Mascaras Quirúrgicas):
https://www.thingiverse.com/thing:4267364
https://cults3d.com/en/3d-model/various/vmo-ss-surgical-mask-strap-coronavirus-covid-19
SURGICAL MASK SEALER (Sellador para Mascaras Quirúrgicas):
https://www.thingiverse.com/thing:4264890