HyperCube Sigma 3D Printer

Some upgrades I've made on Tech2C's Hypercube

The extruder, the spool holder and the LCD cases I will post later because
I need to adjust some measurings.

Configurations are included.

This is my Youtube channel:
https://www.youtube.com/playlist?list=PLLKJfv-aCntELWTE-DZ8PnWBlFQCwG47r

Other parts:
X Carriage 8mm Shaft - https://www.thingiverse.com/thing:4870455
HyperCube Full Graphic LCD Mount - https://www.thingiverse.com/thing:2808601
HyperCube 20x4 LCD Mount - https://www.thingiverse.com/thing:4715912
Universal 2020 Spool Holder - https://www.thingiverse.com/thing:4804124
2020 Corner Bracket - https://www.thingiverse.com/thing:4633339
2020 V-slot Caps - https://www.thingiverse.com/thing:4641848
Bowden Extruder for 2020 Profile - https://www.thingiverse.com/thing:4900775
RAMPS 1.6+ Case - https://www.thingiverse.com/thing:4905227
HyperCube Power Supply Mount - https://www.thingiverse.com/thing:4905252
Hypercube Cable Chain Set - https://www.thingiverse.com/thing:4903982

Printer grip handle 2020 - by DaVinci2000
https://www.thingiverse.com/thing:4599079
T-nut M3 drop-in rotating V-Slot - by DaVinci2000
https://www.thingiverse.com/thing:3050607

V-slot 2020 Profile:
4x 420mm for Z axis
5x 340mm for X axis
6x 303mm for Y axis
2x 320mm for Bed
2x 135mm for Bed

Using the parts with the dimensions above, the printer will be 200x200x210mm.
If you want to use a 310mm heatbed, just increase 100mm lenth on all V-slot parts, shafts and lead screws, and it will be 300x300x310mm.

Hardware:
2x Carbon fiber rods 10x360mm (sold 500mm lenth) for X axis
2x Steel shafts 8x303mm for Y axis
4x Steel shafts 8x300mm fox Z axis
4x Bronze bushings 10mm
8x LM8UU linear bearings
2x LM8LUU linear bearings
2x 250mm T8 lead screws (doesn't matter 2mm or 8mm pitch)
2x T8 nuts the same pitch of the lead screw ( you can use an anti backlash nut)
2x 5x8mm Flex couplers
2x GT2 20 teeth pulleys
6x GT2 16 teeth 3mm inner diameter
2x GT2 "16 teeth" (with no teeth) 3mm inner diameter
3 meters of GT2 belt (don't use that one with steel inside)
1x MK7 extruder gear
3x 608zz bearings ( for filament holder and extruder)
4x Heatbed bolts with spring
1x Small spring for the extruder (a little bit smaller than the heatbed ones)
25x Nylon zip ties
4x Rubber feet (around 20mm diameter)

Bolts, nuts and washers:
20x Allen M6x20mm flat head
73x Allen M5x10mm round head
97x Allen M5x8mm round head
3x Allen M4x10mm cylinder head
2x Allen M3x40mm cylinder head
1x Allen M3x30mm cylinder head
34x Allen M3x20mm cylinder head
7x Allen M3x16mm cylinder head
60x Allen M3x10mm cylinder head
20x Allen M3x6mm cylinder head
5x x Allen M3x6mm without head
169x M5 T-nuts (for V-slot)
50x M3 nuts
41x Nyloc M3 nuts
36x M5 size washers
3x M4 size washers
36x M3 size washers

Electronics:
5x 17HS4401 stepper motors
1x Arduino Mega 2560 board
1x RAMPS 1.6+ (you can use other RAMPS)
1x 80x80mm fan for the RAMPS board
4x Stepper drivers (I'm using DRV8825 on the Blue printer and TMC2100 on the Red one)
1x Full Graphics display (or a 2004 display if you want)
1x Bowden hotend (E3D V6 clone that comes with sensor and fan)
1x 50mm radial fan
2x Endstop modules
1x Inductive sensor (https://www.banggood.com/LJ12A3-4-Z-or-BY-PNP-DC6-36V-Inductive-Proximity-Sensor-Detection-Switch-p-982679.html?cur_warehouse=CN&rmmds=mywishlist)
1x 220x220x3mm Aluminum Heatbed with magnectic build plate
1x 100K thermistor for the heatbed
1x Switching Power Supply (https://www.banggood.com/Wholesale-Switching-Power-Supply-Driver-AC-110V-or-220V-To-DC-12V-30A-360W-Transformer-for-LED-Strip-Light-p-39987.html?akmClientCountry=BR&p=9X051049165582016063&cur_warehouse=CN)
1x AC-01 power socket
Some wires to extend the motor cables

Parts to Print:
40x 2020_Corner_Bracket.STL
04x Bed_Cap.STL
04x Bed_Support_v1.2.STL
02x Cable_Holder.STL
04x Corner_Joint.STL
02x Dual_Bushing_Holder.STL
01x E3D_Clamp_v1.2.STL
01x E3D_Mount_v1.2.STL
01x E3D_Sensor_Mount.STL
01x Fan_Duct.STL
04x Feet.STL
01x X_Carriage_Beltclamp.STL
01x X_Carriage_v1.3.STL
02x XY_Clamp_v1.3.STL
02x XY_Idler_v1.2.STL
01x XY_Joiner_Left.STL
01x XY_Joiner_v1.2.STL
01x XY_Motor_Left.STL
01x XY_Motor_Right.STL
01x Y_Endstop_v1.2.STL
01x Y_Shaft_L_Motor_v1.2.STL
03x Y_Shaft_v1.2.STL
04x Z_Bottom_Shaft_v1.3.STL
04x Z_Carriage_Clamp_v1.3.STL
04x Z_Carriage_v1.4.STL
02x Z_Motor_v1.2.STL
02x Z_Nut_Mount.STL
01x Z_Top_Right_Shaft.STL
03x Z_Top_Shaft_v1.3.STL

HyperCube Full Graphic LCD Mount
4x Flange.STL
1x RDFGC_Back_Mount.STL
1x RDFGC_Front_Mount.STL

Universal 2020 Spool Holder
1x Spool_Holder.STL
2x Spool_Support.STL
2x Spool_Knob.STL

Bowden Extruder for 2020 Profile - 1.75 MK7 608zz
1x Extruder_Base.STL
1x E_Motor_Support.STL
1x Spring_Bolt.STL
1x Extruder_Guide.STL

HyperCube RAMPS Case
4x Flange_RAMPS.STL
1x RAMPS_Reset_Button.STL
4x Spacer_v1.3.STL
1x RAMPS_Back_Mount.STL
1x RAMPS_Fan_Mount.STL
1x RAMPS_Board_Mount.STL

HyperCube Power Supply Mount
1x Power_White.STL
1x Power_Black.STL
1x Power_Mount_Adapter.STL
1x Power_Supply_Mount.STL

HyperCube Cable Chain Set
01x Cable_Chain_End_Bed.STL
01x Cable_Chain_End_Top_Frame.STL
01x Cable_Chain_End_Bottom_Frame.STL
01x Cable_Chain_End_X.STL
44x CableChainLink.stl (22 for X axis and 22 for Z axis)

Printer grip handle 2020 - by DaVinci2000
2x Grip_2in1_v1.1.stl

T-nut M3 drop-in rotating V-Slot - by DaVinci2000
8x T-nut_M3_x1.stl