Introducing the 'Forge Edition: Dual Extrusion Mount' for the E3D Chimera/Cyclops Dual Nozzle Hot-end and Creality Printer
===
This is a compact, fully customisable, tested adapter and mount for the E3D Chimera and Cyclops dual extrusion for most of the Creality Series Printers. Any printer that has the featured mount is compatible.
If you've wanted to create a dual extrusion upgrade: simplify the upgrade with this mount!
---
Update: Version 3 - 10/01/2021
===
Following up from my revision of the Fan Mount last week to version 2, I've added a number of optional parts to give users greater control over the thermodynamic cooling of the Chimera and the directional path of air-flow
---
Key changes:
-
Additional redesigned lower fan mount (Fan Mount V3)
-
Additional lower mount flows air over heat-break and not towards build plate
-
Redesigned fan inlet to reduce the airflow penalty
-
Added air-fins to part-cooler mounts to direct air away from build surface
-
Design choices and further notes explained in manual
Update: Version 2 - 01/01/2021
===
A significant experimental investigation was conducted to elucidate the principle action of cooling within the system to optimise feeding and enable effective retraction performance. Critical insight has been made in respect to how air flows around the mount, Chimera, and how fan placement can better cool the hot-end whilst maintaining a sharp thermal gradient across the heat-break.
---
Key changes:
-
Fully redesigned fan mount (Fan Mount V2)
-
Improved placement of fan to enable air-flow *around* the hot-end
-
Improve and redesigned air-flow channels by reducing the part cooler mount cable tidy
-
Full experimental investigation updated and included in the manual
This complementary set of components will allow you to upgrade your Creality Printer to enable dual-extrusion using the E3D Chimera or Cyclops nozzles/hot-ends. You'll need to purchase those parts if you wish to complete this upgrade, below is a full list with links to the ones I purchased. Continue looking through the photos for more information about the build, and all of the features.
Essential:
1x Creality Printer (with this backplate: https://ebay.us/1oHqdT)
Some other printers use this plate, so if you have it then it will work! See technical drawings for exact sizing if you want to check yours.
1x E3D Chimera/Cyclops or clone
https://e3d-online.com/products/chimera#
Clone:
https://ebay.us/BoTKFy
1x 42mm Stepper Motor + Cable
https://ebay.us/iI2wR8
1x Stepper Driver - I used a TMC2208, but whichever you prefer
https://www.amazon.co.uk/dp/B07WPY4979/ref=cm_sw_em_r_mt_dp_Dsl4Fb0VZ6S15?_encoding=UTF8&psc=1
1x Extruder Gear
https://www.amazon.co.uk/dp/B07SY745CF/ref=cm_sw_em_r_mt_dp_7ql4Fb0142NXA?_encoding=UTF8&psc=1
1x Filament Roll - highly recommend 3DFilaprint ASA X
https://shop.3dfilaprint.com/3d-filaprint-asa-x-iron-grey-175mm-3d-printer-filament-16518-p.asp
M3 Screws - this depends on your configuration, and read the instructions for a full list. I used this pack:
https://www.amazon.co.uk/dp/B07KCT2F6K/ref=cm_sw_em_r_mt_dp_5ul4FbAZJ100Y?_encoding=UTF8&psc=1
Optional:
2x 5015 Fans (if you wish to use the part coolers) - Make sure you get the right voltage! Most boards are 12V
https://www.amazon.co.uk/dp/B07P98KT7V/ref=cm_sw_em_r_mt_dp_0vl4Fb98PCH92?_encoding=UTF8&psc=1
1x Auto Bed Levelling instrument (if not already owned yet desired)
https://www.amazon.co.uk/dp/B0748FJ48N/ref=cm_sw_em_r_mt_dp_wzl4FbWX6W5NJ?_encoding=UTF8&psc=1
1x 40 mm Fan (upgraded from the 30 mm fan that comes with the Chimera/Cyclops)
https://www.reichelt.de/de/en/fan-40x40x10-mm-12-v-0-08-a-fan-ml-4010-12-p76105.html?&nbc=1
Full set of electronics/components if you buy clones/not included in the Chimera Kit (so that’ll be an additional thermistor, heating element, PTFE tubing etc)
A full instruction and build manual is included in the files! Happy Printing!
===
etarfri-org
