Horizontal iPhone Magsafe (StandBy) & AppleWatch Stand

Horizontal Magsafe and AppleWatch Stand

This is a combined MagSafe iPhone and AppleWatch charging Stand that holds the phone horizontally to take advantage of the new StandBy mode in iOS 17.
All cable cutouts fit both USB-A and USB-C cables and all models are compatible with all iPhones that have MagSafe and all AppleWatch models.

Different versions of this design by me can be differentiated by the version number (just in front of the "M") while different suffixes indicate different types of the model at the end of the file name.

Available design variants:

Four variants of V5 are available, and for each variant small and large bezel sizes are available:

1. OriginalDesign: This is my original compact design, only allowing the phone to be held horizontally
2. VerticalPhone: This version is a bit longer and allows the phone to be held vertically, adding a third camera bump cutout for this position (requested by DonWhiteside).
3. 2xMagsafe_noWatch: This is a version that replaces the Apple Watch charging spot with a cutout for a second MagSafe puck, e.g for charging your AirPods (requested by m_reiner on Printables).
4. OnlyPhone: This is a version that removes the Apple Watch charging spot, not replacing it with anything if you don't need it (also requested by m_reiner on Printables).

I also have .stp files of all designs available on my Printables and MakerWorld Profiles, the file system on Thingiverse is just too unorganised for me to upload them here.
Also on Printables are versions where the tolerance around the MagSafe Puck is 0.4mm instead of the 0.2mm on these ones. Use these if you expect larger shrinkage with your filament/printer.
If you wish to use the V3 or V4 files instead of the newer ones, those can also be found on Printables.

Update History

Update 30.10.2023

I just added a new "FlatWatch" version that has the watch connector horiztontally to make charging of AirPods with it easier as requested by Marleyzs. Be advised that this version will therefore not work with closed-loop watch bands. This version is also available in small and large bezel versions.

Update 17.10.2023

SmallBezel versions of each of the original four variants are now available.

Update 05.10.2023

Version 05 is out! This Update adds a retaining mechanism in the cable channels on the bottom of all models.
You need a bit of force to get the cables in, but it is easily possible and leads to secure retention in the channels, preventing them from sticking out.
The AppleWatch Charger mount is also 3mm taller to allow for AppleWatchUltras with cases to better fit.

I also added a new version of the design: "SmallBezels". This version has smaller bezels around the MagSafe Puck for those wishing for a more minimalistic design. Due to the smaller bezel, the cable for the MagSafe-Puck is no longer fully contained in the model.

Update 28.09.2023

I've added versions that have a 0.2mm smaller tolerance on the MagSafe ring (now only 0.2mm bigger than the puck instead of 0.4mm), as the fit wasn't quite as snug as I wanted (I guess my new X1C is just too dimensionally accurate compared to my older Ender 3 Pro).

All the older models can be found below the new ones. They can be distinguished by the last suffix “04mmTol”, compared to the new models with “02mmTol”.

Update 25.09.2023

Version 04 is out! This is a slight redesign of the edges, while also consolidating the naming scheme. All files from Version 03 can now be found at the bottom of the list and can be distinguished by their version number.
V4 is compatible with the iPhone 15 Pro Max and smaller phones, as well as the AppleWatch Ultra and smaller watches.

Update 18.09.2023

The models of V3 are updated with rough dimensions from images of the new phones and should work with all iPhones (I used 15ProMax as a "largest possible scenario").
The Watch Stand is tall enough to fit an AppleWatch Ultra and everything smaller.
The updated original model is the first in the list, simply with the suffix "iPhone15".
The holes for the Cables fit with both USB-A and USB-C charging cables.

Miscellaneous

I printed this in GlowInTheDark Blue PLA which looks very nice at night.

If you want any other file types for a remix or something else just leave a comment and I'll do my best to provide them.