20mm Conduit, 2-Way, right-angled connector for garden trellis/net/frost cover

WARNING: DO NOT USE THIS FOR ELECTRICAL PURPOSES, THE BOLT HOLES (IF USED WITH A BOLT) WOULD GO THROUGH THE WIRES (AN OBVIOUS SAFETY ISSUE), THIS IS FOR GARDEN/OUTDOOR FRAME WORK PURPOSES ONLY.

Are you a gardener, market gardener, or farmer and want to protect your crops? Are you looking for a way to build fanciful 2D/3D frames for netting, frost covers, hoop houses, green houses, trellises, rudimentary shelter with flexible limbs? Then you might want to have a look at this right-angle joiner/connector for 20mm conduit.

WHY 20MM CONDUIT?

I use a lot of 20mm electrical conduit to support my frost covers, netting, and 2D/3D trellises. Some use them for hoop houses and green houses too.

I like the 20mm conduit because it's very cheap, available everywhere, lasts for ages, is flexible, and yet, with the right structure... it's quite rigid. However, the connectors to create fanciful 2D/3D structures aren't available in stores, and the commercial connectors are for electrical purposes only.. no where NEAR strong enough to handle the weight/stresses of bent conduit, particularly in windy locations.

Also, 20mm conduit has one additional benefit over thicker options. If combined with frost covering, you can use 50mm bulldog clips to attach/anchor the fabric/netting, directly around the conduit, this further reinforces the frame too.

WHY A RIGHT-ANGLED 2-WAY?

This is the 2-Way, right angled connector.. which is useful in certain situations. I actually built it with doubling up some of the longer legs on simple dome like trellises/netting/frost cover frames in mind. As fruit trees get bigger, a frame using 20mm conduit gets pretty... wobbly. So it needs more supports to form a honeycomb structure. Also, it can create "broken arch" style 2D trellises, or even 3D with some creativity.

Why limit yourself to joints with 2 sockets?

I've also created a whole series of connectors for 20mm conduit. Seriously, why be boring with rectangular frames and trellises?

1- Way "Stake styled" Anchor found here:
https://www.thingiverse.com/thing:6228095

1-Way "Screw down" anchor found here:
https://www.thingiverse.com/thing:6228135

2-Way "Straight" Connector:
https://www.thingiverse.com/thing:6187349

2-Way "L" or "right angle" connector:
https://www.thingiverse.com/thing:6188056

3-Way T-connector found here:
https://www.thingiverse.com/thing:6163480

3-Way, Y-connector found here:
https://www.thingiverse.com/thing:6181085

4-Way "cross" connector, found here:
https://www.thingiverse.com/thing:6163584

5-Way "star?" connector, found here:
https://www.thingiverse.com/thing:6181104

6-Way connector found here:
https://www.thingiverse.com/thing:6181111

7-Way connector found here:
https://www.thingiverse.com/thing:6187567

8-Way found here:
https://www.thingiverse.com/thing:6167506

Half 8-Way Connector:
https://www.thingiverse.com/thing:6195584

Quarter 8-Way Connector:
https://www.thingiverse.com/thing:6196723

9-Way found here:
https://www.thingiverse.com/thing:6190630

10-Way found here:
https://www.thingiverse.com/thing:6182651

WHY THE FLAT DESIGN?

My design basis (for all of these connectors) has three things going for it:

It can be easily printed without ANY supports whatsoever.
It is FAR stronger than commercial connectors, and takes advantage of "laid flat" orientation to minimise the weaknesses involved in layered FDM printing) and if that isn't enough...
I included M4 bolt holes so you can simultaneously:

a) Lock the conduit into the connector using the bolt. (Drill a hole through the conduit first, obviously)

b) Use the M4 bolt, nut and washers to ensure the layers of the connector are held together, even under significant strain. Hand tight is enough, you don't want to crush the plastic.

NOTES:

While I don't recommend PLA for this purpose, (It's exposed to UV and water after all) I chose to use PETG and protect the conduit from UV by wrapping it in duct tape. It's working well so far, but we'll see how it's going after a couple of seasons.