Non-Quick Connect OmniStand Compatible Filament Spool Stands

PRINTER COMPATIBILITY

• FlashForge Dreamer
• Dremel 3D Idea Builder

These stands are compatible with all OmniStand Filament Spool rods and spacers.

Unlike the OmniStand, these stands do not have quick connect bases, and must be directly attached with screws. They cannot be easily replaced or changed without unscrewing them.

For additional information, compatible filament spool rods and spacers see the OmniStand found here: http://www.thingiverse.com/thing:652415

FILAMENT SPOOL COMPATIBILITY

When using a 100 mm filament spool rod (found here: http://www.thingiverse.com/thing:652415), the three filament rod hole positions are optimized for 3 different filament spool size categories: up to 184x65 mm (7.24x2.55"), up to 230x65mm (9.05x2.55"), and up to 190x77 mm (7.48x3.03"). For slightly wider spools see here: http://www.thingiverse.com/thing:667473

Using the 100 mm filament spool rod the stand was tested to fit the following filament spools inside the FlashForge Dreamer and Dremel 3D Idea Builder:

• ASAPTech TPE (0.7 kg white tested)
• ColorFabb (0.75 kg CopperFill tested)
• Dremel (all filament tested)
• ESun (0.5 kg bronze tested)
• Filamex (0.5 kg spools of ABS/PLA tested)
• FlashForge Dreamer (all filament tested)
• Hatchbox (1 kg and 0.45 kg spools of ABS/PLA tested)
• Magic Cube (0.45 kg ABS tested)
• MG Chemicals (0.25 kg of PLA/ABS tested)
• NinjaFlex (0.5 kg Fire color tested)
• Taulman (0.45 kg of T-glase tested)
• USAFilament (0.5 kg PVA tested)
• Zen Toolworks (1 kg wood filament tested, others might not fit)

Filament spools tested that cannot fit inside the FlashForge Dreamer or Dremel 3D Idea Builder:

• Filament Outlet (1 kg spool of HIPS tested)
• Gizmo Dorks (1 kg spool of HIPS tested)
• Shaxon (1 kg spool of ABS tested)
• USAFilament (1 kg spool tested)

FILAMENT STANDS

Each single piece stand has three rod holes to allow the filament rod to better accommodate different sized filament spools.

The bottom rod hole is specifically designed to fit FlashForge Dreamer and Dremel filament spools allowing them to go down into the filament depression at the bottom of the printer, maximizing clearance space in the printer. Other filament spools up to 184x65 mm should fit, but some spools might require an additional spacer for the spool's hole.

The middle rod hole is designed for filament spools that are thin enough to fit into the filament depression at the bottom of the printer, but too large to fit the standard FlashForge Dreamer and Dremel filament stand. Spools up to 230x65mm should fit, but some rolls might require an additional spacer for the spool's hole.

The top rod hole is designed for filament spools that are too fat to fit into the filament depression at the bottom of the printer. Spools up to 190x77 mm should fit (or 190x82.5 mm if using the maximum length rod found here: http://www.thingiverse.com/thing:667473), but some spools might require an additional spacer for the spool's hole.

FILAMENT ROD SPACERS

For compatible filament rod spacers see:

http://www.thingiverse.com/thing:652415

FILAMENT RODS

For compatible filament rods see:

http://www.thingiverse.com/thing:652415

http://www.thingiverse.com/thing:667473