以下是整理後可直接貼到 Thingiverse 的版本，已加入 V2.0 / V2.1 Changelog，並在主要說明中補上 V2.0 以後需要 M2 x 6mm plastic self-tapping screws x3。
🌐 English Version
The 3D-printed version of Part-C for the PicoBETH HW2 hardware layout, an open-source badminton stringing machine, simplifies the assembly process and improves the convenience and reliability of cable management.
Starting from V2.0 and later, the cable fixing plate has been separated from the main body. This makes the 3D-printed part less likely to break when securing wires.
- M5 x 80mm screws x2 (for mounting to the Load Cell): Please ensure the use of standard M5 washers and tighten with a torque value of 2N.m.
- M4 x 16mm screws x4 (for mounting to the sliding table base): Please ensure the use of standard M4 washers and tighten with a torque value of 1.5N.m.
- M2 x 6mm plastic self-tapping screws x3 (required for V2.0 and later): Used to install the separated cable fixing plate.
- Material: Avoid using PLA, as its strength deteriorates over time. It is recommended to use high-strength materials for printing.
- Infill: This component is subject to significant stress; please set the infill density to 100% to extend its lifespan.
Note: Failure to use washers or to follow the specified torque values may result in component damage. Please pay close attention!
Changelog
V2.1
- Added a dust cover locking clip design.
- This rail dust cover design must be used together with HW2 Simple Dust Cover V2.0.
- HW2 Simple Dust Cover V2.0 is not released yet.
V2.0
- Separated the cable fixing plate from the main body, making the 3D-printed part less likely to break when securing wires.
- Requires M2 x 6mm plastic self-tapping screws x3 for installation.
For the complete assembly process of the PicoBETH badminton stringing machine, please refer to my GitHub and YouTube channel, where detailed tutorials and explanations are provided:
Welcome to My YouTube Channel!
Your subscription is my biggest motivation to keep creating. Thank you for your support!
Subscribe Here
🌏 中文版本
開源羽毛球穿線機 PicoBETH HW2 硬體佈局組件 C 的 3D 列印版，可簡化製作過程，並提升線材固定的便利性與可靠性。
自 V2.0 以後版本 起，固定電線用的固定片改為獨立分離式設計，可降低固定線材時造成 3D 列印組件斷裂的風險。
- M5 x 80mm 螺絲 x2（固定至 Load Cell）： 請務必使用標準 M5 螺絲墊片，並以鎖緊扭力值 2N.m 安裝。
- M4 x 16mm 螺絲 x4（固定至滑台座）： 請務必使用標準 M4 螺絲墊片，並以鎖緊扭力值 1.5N.m 安裝。
- M2 x 6mm 塑膠自攻牙螺絲 x3（V2.0 以後版本需要）： 用於固定分離式電線固定片。
- 材質： 避免使用 PLA 材質，因其強度會隨時間劣化。建議使用高強度材質進行列印。
- 填充： 此組件承受較大受力，請將填充密度設為 100% 以延長使用壽命。
注意： 缺少螺絲墊片或未按照設定鎖緊扭力值操作，可能導致組件損壞，務必留意！
更新紀錄
V2.1
- 加入防塵固定卡扣設計。
- 此軌道防塵設計需搭配 HW2 Simple Dust Cover V2.0 使用。
- HW2 Simple Dust Cover V2.0 尚未發佈。
V2.0
- 將電線固定片改為分離式設計，使固定電線時 3D 列印組件更不容易斷裂。
- 安裝時需要使用 M2 x 6mm 塑膠自攻牙螺絲 x3。
完整的 PicoBETH 羽毛球穿線機製作流程，請參考我的 GitHub 與 YouTube 頻道，提供詳細教學與說明：
歡迎訂閱我的 YouTube 頻道！
您的支持是我創作的最大動力，感謝您的關注！
點此訂閱
kuokuo702
