Bass Guitar

locatiadesigns

Step‑by‑Step Printing Instructions

1. Prepare the 3D Model Files

Download Files: Retrieve the STL (or equivalent) files for the bass guitar and get familiar with the design. I recommend confirming that components from your amazon kit matches the dimensions within the model. I designed these models based on the one I purchased. I do not know how much variability there is between guitars.

Review Design Details: Confirm that the model includes the following features:

Measure steel rod length and diameter before printing. Adjust the hole based on the rods you received.
Confirm that the neck will fit in the pocket.
Mounting holes pre‑designed for brass heat‑set inserts.
The holes for the neck are through holes and is designed to be used with the metal plate for maximum durability.

2. Set Up in Bambu Studio

Material: Bambu Labs PETG HF for the internal body components, PLA Basic for dark blue plates on the front and back of the guitar, PLA Matte for the light blue stripes, PETG HF for the orange stripes.

Layer Height: Set to 0.2 mm for a good balance of resolution and speed.

Infill: Use 25% infill – this provides weight reduction while keeping the structure light.

Perimeters (Wall Loops): Configure the slicer for 7 perimeters to create a robust outer shell. This is already set in Bambu Studio for the primary structural components.

Additional Settings: Dry out the PETG prior to use for best printing quality. Use the Bambu Labs recommended temperatures and speeds for PETG HF as outlined in the filament’s datasheet. Ensure that your print bed is properly prepared (with a PEI or textured PEI surface and glue if needed).

3. Print the Guitar Body

Start the Print: Launch your print job and monitor the first few layers to ensure proper adhesion.

Post‑Processing: Once printed, remove any support structures carefully. Lightly sand any rough edges if necessary (only on the internal surfaces that aren't seen).

Fit Check: Check the fit of all the bass guitar components before proceeding. Make adjustments to 3D printed parts if needed.

Heat‑Set Inserts: Use a heat‑set tool to install brass inserts at the designated mounting points for the bridge and neck attachments. The brass inserts used are for 4-40 and 2-56 screw sizes. There are ~28 total 4-40 inserts and 6 total 2-56 threaded inserts. The only location the 2-56 inserts are used is for the dark blue control plate.

Screwing the Components together: First screw all the internal components together to form the internal body structure of the guitar. These are all the cream colored components.

Bottom Plates: super glue the bottom plates to the guitar first.

Top Plates: super glue the top plates starting with large dark blue plates on the right and move sequentially to the left. This is important so all the plates fit together properly.

Assembling the Kit Components

4. Prepare the Neck

Watch this video to learn how to prep the guitar neck:

5. Reinforce with the Metal Plate

Metal Plate Preparation: The metal plate should come with a plastic piece that is placed between the 3D printed guitar and the metal plate. It also comes with the screws required to attach the neck.

Attach the Plate: Position the plate on the back side of the printed body. Secure it using four screws that pass through the PETG into the wooden neck. This plate will distribute the tensile load from the neck screws, reducing local stresses in the plastic.

6. Assemble the Bridge

Mount the Bridge:

With brass inserts already in place on the guitar body, position the bridge so that its mounting holes align.
Secure the bridge with the seven 4‑40 screws. The wide distribution of screws (and the accompanying metal plate backing) ensures the string tension load is well spread across the body.

7. Final Assembly and Setup

Tuners: Attach the tuners.

Stringing: Once the main assembly is complete, install your four bass strings. The design assumes each string exerts approximately 30 lbs of tension, totaling 120 lbs.

String Guide: If a pilot hole isn't present for the string guide for the “D” and “G” string, drill a pilot hole.

Tuning & Setup: Tune the guitar and check the action. The reinforced neck joint and metal plate should keep the structure rigid under string tension. Adjust the bridge and truss rod according to your setup needs.

Inspect: Look over all fasteners (screws, inserts, and neck bolts) to ensure they’re tight and the assembly is stable.

Tips for Success

Dimensional Review: Review the part dimensions from the kit, threaded inserts, and steel rods to ensure everything has enough clearance.

Component Alignment: It is important to check all components with the center/main body print first. Make sure the pickups fit and the string will align with the neck. You may need to adjust the hole position on the print to account for the variability in hole placement in the guitar kit you purchased. Do not glue until you know everything will align.

Monitor Print Quality: Ensure that your 3D printer is well-calibrated to minimize layer adhesion issues.

Reinforce Strategically: The metal plate not only reinforces the neck joint but also provides a backup against long‑term creep. Check periodically for any signs of stress or loosening.

Environmental Control: Keep your guitar in a stable temperature environment.

Patience: For this project patience is your ally! Take your time and enjoy the process. It is easy to make mistakes if you rush it.

By following these step‑by‑step instructions, you’ll have a durable, and custom 3D‑printed guitar! Enjoy the build process and the unique sound of your handcrafted instrument!