Stretching bamboo sword

伸缩竹子剑

进群的可以看我的简介

Boost Me助力一下吧亲！！

ps：小号28g左右的伸缩剑已经发送，28g 小号竹子剑宝宝 来自 wannawow(摆烂猫) MakerWorld：免费下载 3D 模型

 

ps:第一次做伸缩剑，可能有些不熟悉，有建议请随时提出，感谢。

ps:盖子我没有加支撑（不好拆），可能会有点拉丝，但是不影响拧上去，也不影响外观。如果有更好的建议请反馈，我好再改。注意，盖子是逆着转

本模型出于省料跟时间的考虑，去掉重刷塔的设置且同时部分没有设置分层，已经进行了验证（在文的最后）。算是新的尝试吧，希望大家都能打印成功。  

 

PS: This is my first time making a telescopic sword, and I may not be familiar with it. If you have any suggestions, please feel free to ask. Thank you.

PS: I didn't add any support to the lid (it's difficult to remove), it may be a bit brushed, but it doesn't affect screwing it on or its appearance. If you have any better suggestions, please provide feedback so that I can make further changes. Note that the lid is turned upside down

This model has been validated (at the end of the article) for the sake of saving materials and time by removing the setting of heavy brushing towers and not setting up layers in some parts. It can be considered a new attempt, I hope everyone can print successfully.   

打印耗材：

暂时推荐两种颜色。

1多色：使用绿色渐变（可以参考p家的春夏秋冬系列）或者是bambu pla 的浅绿。然后配合bambu pla slik的金色进行打印。

我的配置没有放置冲刷塔。其实也感觉没必要放置。

 

2单色或者绿色或者金色都挺好看的

Printing consumables:

I temporarily recommend two colors.

1. Multicolor: Use a green gradient (refer to P's Spring/Summer Autumn/Winter collection) or light green from Bambu PLA. Then print in gold with Bambu PLA Slik.

My configuration does not include a flushing tower. I actually feel like there's no need to place it.

 

Monochrome, green, or gold all look pretty good

款式：

1基础款：整个剑需要一体打印，同时中间的每一节没法拿出。但是效果最好。

优点：比较稳固，不怕使劲的甩动，而且每一节的伸缩，更加符合竹子的造型

缺点：短了一点（可以看图片）

 

2简化款：这个版本每个内部每一节可以拿出来。

优点：内部可以拿出，减少了因为打印机失误而造成的模型损坏。同时支持分件打印

缺点：更像一根棍子，而不是竹子

 

3：加长版，就是调整了每一节之间的间隙，可以让剑可以伸缩更长。

优点：长！！！

缺点：太长了容易折断

1. Basic version: The entire sword needs to be printed as a whole, and each section in the middle cannot be taken out. But the effect is the best.

Advantages: It is relatively stable, not afraid of strong shaking, and the expansion and contraction of each section is more in line with the shape of bamboo

Disadvantage: It's a bit short (as shown in the picture)

 

2 Simplified version: Each internal section of this version can be taken out.

Advantages: It can be removed internally, reducing model damage caused by printer errors. Simultaneously supporting split printing

Disadvantage: More like a stick than bamboo

 

3: The extended version adjusts the gap between each section, allowing the sword to stretch and contract longer.

Advantages: Long!!!

Disadvantage: Too long and prone to breakage

配置：

注意，多色打印给了两个配置，既配置1（对耗材要求高）跟配置2稳健配置

稳健配置：对应右边，分层多色，打印出来会出现更多的金色环

配置1（对耗材要求高）对应左边，更加像竹子

 

Note that multi-color printing provides two configurations, namely Configuration 1 (which requires high consumables) and Configuration 2 for robust configuration

Robust configuration: Corresponding to the right side, layered with multiple colors, more golden rings will appear when printed

Configuration 1 (high requirements for consumables) ：corresponds to the left side, more like bamboo

ps：图片为mini版本举例

 

Style:

1. Basic version: The entire sword needs to be printed as a whole, and each section in the middle cannot be taken out. But the effect is the best

2 Simplified version: Each internal section of this version can be taken out.

3: The extended version adjusts the gap between each section, allowing the sword to stretch and contract longer. But the cost is easy to break (everyone knows)

 

ps：图片是加长与基础或者简化版本的区别。

PS: Images are the difference between extended and basic or simplified versions.

配件：

Accessories:

本模型配件有4个：

1：带环的上端盖子

This model has 4 accessories:

1: Upper cover with loop

2：不带环的上端盖子

2: Upper end cap without loop

3：下端的盖子（用来防止剑滑滑出来）

PS:根据测试有些耗材盖子可能不开好盖上，请使用刮刀轻微刮削内部小球，以达到你满意的松紧度。

3: Bottom cover (used to prevent the sword from slipping out)

打印测试历程：

1p家的春夏秋冬系列加彩多屋的金色,通过

2竹耗材（宁美）加金色，通过

3bambu绿色加bambu金色 通过

4兰博暗金色加bambu 绿色，有一点粘结，已改正配置。

5petg测试  通过，就是打印会出现小的瑕疵。可能是料子的原因。

 

Print testing process:

1p's Spring/Summer Autumn/Winter Collection with Colorful Multi House Gold, Through

2 bamboo consumables (Ningmei) with gold color, through

3bambu green+bambu gold by

4 Lambo Dark Gold with Bambu Green, slightly adhesive, configuration has been corrected.

The 5petg test passed, indicating that there may be minor flaws in the printing. It may be due to the material.