上海中心大厦-无AMS，无五金 Shanghai Tower-No AMS

上海中心大厦模型-无需AMS，无需五金件
Shanghai Tower-No AMS

高度66cm
height: 66cm

你需要的东西：透明的PETG材料（无色&蓝色）、榔头、强烈建议打印版涂胶。如果你不能保证模型不会被意外肘飞的话，模型的连接处建议涂胶（502之类）
What you need: Transparent PETG material, hammer, glue on the plate is strongly recommend. In case of falling apart, please glue the parts together.

我在网上找了很久都没有找到很好的上海中心大厦模型，因此就自己做了这个，感觉质感很不错。阳光下甚至可以看到幕墙下核心部分。
I've been looking for models for Shanghai Tower for a while and nothing suitable was found so I made this myself. You can see the brilliant texture and can even see the core under the sun.

注意事项Printing instructions

材料2（蓝色）与材料3（白色）请一定要使用对应颜色的透明PETG，这样才能看到内部。
材料5（米黄色）是不透明的PETG，可以用白色代替

##很重要！！先打印盘4的夹层玻璃环，因为盘3打印过程中需要按照配置文件内的暂停打印将打印暂停，然后将玻璃环放入继续打印

再打印盘5与盘8的窗户部分，因为盘7打印时会暂停3次，依次将盘5的floor部件放在前方，盘8的side window插在左侧面，盘8的front up插在前面（需要略微弯曲找到特定角度才能插好）

盘5的floor打印时向下的面放入时也向下，盘8的所有窗户打印时向下的面安装时向外，对side window方向存疑可以在盘5的side上面比划一下
很建议涂胶，包括底面积很大的零件，因为本人已经因为翘边打废一盘了
蓝色的幕墙上面几层公差有点小，实测用榔头可以砸进去
建议在每两层的核心筒中间涂胶，这样可以防止被肘飞，并且不影响质感
不要使用花瓶模式或者降低风扇转速或打印速度来追求更透明的外壳，因为这会降低冷却速率使外壳形状不正确。
除了2号与3号耗材丝需要用PETG来追求质感，其它耗材可酌情更换（材料2的透明蓝会给幕墙带来一抹可爱的淡蓝色）

Please use transparent PETG for material2(blue) and material3(white) so that you can see the inside.
Material5(light yellow) is intransparent PETG and can be replaced by white ones.

###VERY IMPORTANT!!! Print glass rings in plate4, because plate3 will be paused (hopefully work as set in the file) during the printing, you have to put the rings on the models and then continue printing.
Then print plate5&8 for the windows. bacause plate7 will pause 3 times, in turns you need to put FLOOR in plate5 on the front, SIDE WINDOW in plate8 on the left, and then insert FRONT UP in plate8 on the front.(bend a little bit and carefully find the right place to put)

Face facing down when printing in FLOOR in plate5 still faces down when inserting. Every face facing down in plate8 faces out when inserting. Compare it on SIDE in plate5 if confused about the direction of SIDE WINDOW in plate8
Glue on the plate (including those with huge bottom surface) is strongly recommend since I myself has wasted plates of materials bacause of curling up.
Blue windows is a little bit tight, but can be hammered in.
You can apply glue between cores, and it won't affect the texture.
Do not use vase mode or turn down the fan for brighter shells, it will lead to lower cooling speed and  wrong shape.
Material2&3 should be PETG for texture, but other materials can be replaced.(transparent blue for material2 will bring a lovely sky blue to the building)

祝你打印成功！
Hope it works well!