Enjoy my new 3d design for a brushless micro quadrocopter. Based on the brushed quadrocopter idea of
stlyesuxx. It uses 2.5 inch propeller and 2S lipo in combination with brushless dys 7000kv 1104 motors. The AUW of the micro quadcopter is around 140grams using a 850mah battery pack.
Thrust should be around 150 grams per motor with 2S and 2540 tribalde props.
So it has quite some punch :)
If you crash, it might break, but it still does an good job at protecting your components. Most times, you will be able to fix the frame using superglue or a print pen. Moving the components to a new print is done within minutes.
My flightcontrolboard is flashed with betaflight 3.2.4 at standart PID settings and with dynamic filter enabled. Only rates are adjusted.
If you want to add a small action cam, you might need to retune your pid and fly acro a bit less hard. But it willy carry a mobius or runcam 2, so you get some nice 1080p footage from it.
The runcam split mini seems to be a perfect fit for this frame. It just needs good dampening.
Of course i will get you updated as soon as i find a good solution. For now i get some tearing in the footage.
If you have some flexible filament you may print the tpu motor mounts to reduce vibrations on your frame. For me this worked quite good.
You may also try to print the short standoffs using tpu. In addition i mounted my fc board onto slices of "oropax" earplugs. This works quite well.
You may mount all the usual FC sizes to this frame. 30.5mm, 20mm, 16mm
This setup is able to carry a runcam split 1/2 or runcam split mini.
It will fit M3 screws for the frame standoffs and the 30mm flightboards. (10x)
Use M2 screws for the flight boards with a diameter of 20mm or 16mm (4 - 12x)
I have also added a tiny bit screwdriver, in case you have troubles reaching the cam mount, you might find it usefull.
I would be very happy to see your make and get some feedback :)
Update 1:
- Fixed the meduim standoff floating.
- Added standoffs with mounting holes for Runcam Split Mini.
Update 2:
- Added better standoffs for Runcam Split Mini
- Added alternate frame design
Update 3:
- Added another frame design - much better stability but a bit more weight
--------------------
Components:
Screws & Nuts:
6x M2 7mm screws - duct mount (can be replaced with longer screws)
3x M2 7mm screws - topplate mount (can be replaced with longer or shorter screws)
3x M2 10mm screws - duct and standoff mount
16x M2 3mm screws - motor mount (should be the regular screw length that comes with your motors.)
9x M2 nut
M2 screwset:
M2 screw set
Motors:
DYS - 1104 7000KV
Props:
Gemfan flash - 2540 - triblade
ESC:
Racestar 4 in 1 12A using DSHOT 600
Recommended flightcontrol:
Omnibus F4 with OSD
Lipo 2S
2S Lipo 60C
--------------------
FPV cam/transmitter combo:
Eachine TX06(supports smart audio)
or
FPV camera:
Runcam Split Nano
and
FPV transmitter:
Eachine NANO VTX
--------------------
5V active Buzzer (take it, if you dont want to search your quad for hours and hours.)
Buzzer and LED
Further you need:
Transmitter and receiver of your choice. I use the Flysky I6 with SBUS mod
Flysky I6 with A8S combo
FPV goggle:
Kylin Vision
--------------------
Videos
Build and first testflights:
https://youtu.be/CC2rdLjDmQU
Will it freestyle?
https://www.youtube.com/watch?v=ssAvmCJ2Ric
Runcam 2 onboard test:
https://www.youtube.com/watch?v=El74EtgDLiM
Runcam Split Mini onboard test:
https://youtu.be/Gr55fPuu5v0
https://youtu.be/FNwA3jymqHU
https://youtu.be/l7ptdVGe1NE
https://www.youtube.com/watch?v=4mNiX74SHqM
https://www.youtube.com/watch?v=7xdDh7LYwDw
Firmware
Awesome flightcontroller firmware:
Betaflight 3.2.4 https://github.com/betaflight/ (Open Source)
Noctaro
